Blade 180 QX HD RTF BLH7400 Hoja De Datos
Los códigos de productos
BLH7400
15
EN
Stability Mode Calibration
1. Ensure all trims are centered.
2. Power on the transmitter and move the throttle stick to full throttle.
3. Ensure the transmitter is in Stability High or Low Angle Mode.
4. Hold full up elevator.
5. Connect the fully charged fl ight battery in the quadcopter.
6. Both LEDs will fl ash red twice, then blue twice for a few seconds.
7. When the LED turns solid blue, lower the throttle and return the elevator to center.
8. Raise the throttle to bring the quadcopter to a hover.
9. Use the trims on the transmitter to eliminate any drifting, allowing for a stable hover.
10. While in a stable hover, press and hold the camera trigger on the transmitter for 5 seconds. The quadcopter is now
2. Power on the transmitter and move the throttle stick to full throttle.
3. Ensure the transmitter is in Stability High or Low Angle Mode.
4. Hold full up elevator.
5. Connect the fully charged fl ight battery in the quadcopter.
6. Both LEDs will fl ash red twice, then blue twice for a few seconds.
7. When the LED turns solid blue, lower the throttle and return the elevator to center.
8. Raise the throttle to bring the quadcopter to a hover.
9. Use the trims on the transmitter to eliminate any drifting, allowing for a stable hover.
10. While in a stable hover, press and hold the camera trigger on the transmitter for 5 seconds. The quadcopter is now
calibrating input from the sensors and transmitter.
11. Release the camera trigger and land the quadcopter. Upon landing, the LEDs should fl ash red then blue. When the
LEDs repeat with one blink per color, the calibration is complete.
12. If only the red LED is fl ashing, the calibration has failed. Repeat the process.
13. Disconnect the battery, then return the trims to center.
13. Disconnect the battery, then return the trims to center.
Troubleshooting Guide
Problem
Possible Cause
Solution
Quadcopter control response is
inconsistent or requires extra trim
to neutralize movement.
inconsistent or requires extra trim
to neutralize movement.
Aircraft not initialized on a level surface.
Disconnect the fl ight battery, center the control
trim and re-initialize the quadcopter.
trim and re-initialize the quadcopter.
Battery not correctly placed in
battery slot.
battery slot.
Adjust battery position so quadcopter balances
in the center of the frame.
in the center of the frame.
Quadcopter will not respond to
throttle.
throttle.
Throttle too high and/or throttle trim is
too high.
too high.
Reset controls with the throttle stick
and throttle trim at the lowest setting.
and throttle trim at the lowest setting.
Quadcopter moved during initialization.
Disconnect the flight battery and re-initialize
the quadcopter while keeping the quadcopter
from moving.
the quadcopter while keeping the quadcopter
from moving.
Throttle channel is reversed.
Disconnect fl ight battery, reverse the throttle
channel on the transmitter,
recconnect fl ight battery.
channel on the transmitter,
recconnect fl ight battery.
Quadcopter does not function
and smells burnt after connecting
the fl ight battery.
and smells burnt after connecting
the fl ight battery.
Flight battery connected with the wrong
polarity.
polarity.
Replace the 5-in-1 board. Connect the fl ight
battery noting proper polarity.
battery noting proper polarity.
Quadcopter has reduced fl ight
time or is underpowered.
time or is underpowered.
Flight battery charge is low.
Completely recharge the fl ight battery.
Inadequate power to fl ight battery charger.
Use a different USB power source for the
charger.
charger.
Flight battery is damaged.
Replace the fl ight battery and follow the fl ight
battery instructions.
battery instructions.
Flight conditions might be too cold.
Make sure the battery is warm (room tempera-
ture) before use.
ture) before use.
LED on receiver fl ashes rapidly
and aircraft will not respond to
transmitter (during binding).
and aircraft will not respond to
transmitter (during binding).
Transmitter too near aircraft during bind-
ing process.
ing process.
Power off the transmitter. Move the transmitter
a larger distance from the aircraft. Disconnect
and reconnect the fl ight battery to the aircraft.
Follow the binding instructions.
a larger distance from the aircraft. Disconnect
and reconnect the fl ight battery to the aircraft.
Follow the binding instructions.
Bind switch or button was not held while
transmitter was powered on.
transmitter was powered on.
Power off transmitter and repeat bind process.
Aircraft or transmitter is too close to large
metal object, wireless source or another
transmitter.
metal object, wireless source or another
transmitter.
Move aircraft and transmitter to another
location and attempt binding again.
location and attempt binding again.
Full up elevator