Texas Instruments BQ24073 Evaluation Module BQ24073EVM BQ24073EVM Hoja De Datos
![Texas Instruments](https://files.manualsbrain.com/attachments/b46f99d826b2b0e0e5f558c5fb6483942eb9216b/common/fit/150/50/c15ea36eb1fb1cce99a3b94668675bfc78ce832d8d727d9a7bb51a125510/brand_logo.gif)
Los códigos de productos
BQ24073EVM
OUT
J2
IN
GND
R8-ILIM
TMR
J1
5.25 VDC
J4
J3
EN1
JMP5
JMP4
EN2
CE
JMP3
VSS
VSS
BA
T+
VSS
TS
R16-TS
JMP2
JMP2
R10-ITERM R11-ISET
VSS = GND
TD
bq24072/3/4/5 EVM
HPA282 - UUT
or
bq24079 (T)
R1
10 W
DMM
#2
DMM
#1
DMM
#3
R2
0.1 W
4.2VLi-IonCell
P/S
#1
CH 1
CH 2
CH 4
CH 3
Test Summary
www.ti.com
Table 3. bq240xx
Jumper
'72
'73 or '230
'74 or '232
'75
JMP1
RES–TMR
RES–TMR
RES–TMR
RES–TMR
JMP2
TD–Vss
TD–Vss
TD–Vss
TD–Vss
JMP3
CE–Vss
CE–Vss
CE–Vss
CE–Vss
JMP4
EN2–HI
EN2–HI
EN2–HI
EN2–HI
JMP5
EN1–Vss
EN1–Vss
EN1–Vss
EN1–Vss
Figure 1. Test Diagram
4.3
Test Procedure
1. Verify that the equipment and EVM is set up according to the preceding section.
2. Verify that V
2. Verify that V
OUT
is approximately equal to V
BAT
3. Turn on P/S#1, +5.25-Vdc supply to the UUT.
4. Verify V
4. Verify V
BAT
is between 2.4 Vdc and 3 Vdc, and the charger is in precharge state: LEDs CHG (D1) and
PGOOD (D2) are on. If V
BAT
is above the low-voltage threshold (V
(LOWV)
~3 V), then the IC is in
fast-charge mode. If the IC is in fast charge, skip step 7.
5. Verify DMM#3, I
BAT
is ~9 mV or ~0.09 A
6. Verify that V
OUT
for bq24072 is ~200 mV above the battery voltage or a minimum of 3.4 Vdc. For
bq24073/4 verify that V
OUT
is ~4.4 Vdc. Verify that bq24075/9(T) is ~5.5 Vdc for V
IN
> 5.6 V and equal
to V
IN
for Vin < 5.6 V.
7. Allow the battery to charge until V
BAT
is between 3.3 Vdc and 4 Vdc. The charger delivers the
programmed constant current to the battery unless the input cannot source the required current.
8. Verify I
BAT
is ~88 mV or ~0.9 A (for a 1-k
Ω
resistor on ISET).
9. Verify V
OUT
: bq24072 – ~200 mV above the battery voltage.
10. Set JMP5 (EN1) to HI, and verify that the chip has been disabled, D1 (CHG) has turned off, and the
P/S#1 current has dropped to zero. The internal battery FET must be on, connecting the BAT pin to
the OUT pin. Verify that the voltage on the OUT pin is close to the battery voltage. See
the OUT pin. Verify that the voltage on the OUT pin is close to the battery voltage. See
for
4
bq24072/3/4/5/9(T) and bq24230/2 1.5-A Single-Chip Li-Ion —and Li-Polymer
SLVU274C – November 2008 – Revised May 2010
Charge Management IC EVM
Copyright © 2008–2010, Texas Instruments Incorporated