Voltcraft PS-200HTPPocket scalesWeight range bis 200 g PS-200HTP Hoja De Datos

This product is designed to weigh objects of up to 200 g in weight. The weight can also 

be displayed in ounces (oz) or carat (ct) and troy ounce (ozt). In addition, the product 

can also display the number of units weighed. Power is supplied via two batteries (type 

AAA). The product should only be used in dry indoor areas. The product is not suitable 

for medical or commercial uses.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. 

If you use the product for purposes other than those described above, the product may 

be damaged. In addition, improper use can cause hazards such as short circuiting, fire,

electric shock etc. Read the instructions carefully and keep them. Make this product 

available to third parties only together with its operating instructions.

Pocket scale

•

Tray

•

Pouch

•

2 x battery (type AAA)

•

Operating instructions

•

The device is not a toy. Keep it out of the reach of children and pets.

•

Do  not  leave  packaging  material  lying  around  carelessly.  These  may 

•

become dangerous playing material for children.
Protect  the  product  from  extreme  temperatures,  direct  sunlight,  strong 

•

jolts, high humidity, moisture, flammable gases, vapours and solvents.
Do not place the product under any mechanical stress.

•

If it is no longer possible to operate the product safely, take it out of operation 

•

and  protect  it  from  any  accidental  use.  Safe  operation  can  no  longer  be 

guaranteed if the product:

is visibly damaged, 

 -

is no longer working properly, 

 -

has been stored for extended periods in poor ambient conditions or 

 -

has been subjected to any serious transport-related stresses.

 -

Please handle the product carefully. Jolts, impacts or a fall even from a

•

low height can damage the product.
Also observe the safety and operating instructions of any other devices 

•

which are connected to the product.
Operation  in  environments  with  strong  electromagnetic  radiation  might 

•

involve deviations of the indicated values.
Loads  (weighing  object)  should  not  be  left  resting  permanently  on  the 

•

scale. This might damage the measuring mechanism.

Correct  polarity  must  be  observed  while  inserting  the  (rechargeable) 

•

batteries.
(Rechargeable) batteries must be kept out of reach of children. Do not 

•

leave (rechargeable) batteries lying around, as there is risk, that children 

or pets swallow them.

(Rechargeable) batteries should be removed from the device if it is not 

•

used for a long period of time to avoid damage through leaking. Leaking 

or  damaged  (rechargeable)  batteries  might  cause  acid  burns  when 

in contact with skin, therefore use suitable protective gloves to handle 

corrupted (rechargeable) batteries. 
All  (rechargeable)  batteries  should  be  replaced  at  the  same  time. 

•

Mixing old and new (rechargeable) batteries in the device can lead to 

(rechargeable) battery leakage and device damage. 
(Rechargeable)  batteries  must  not  be  dismantled,  short-circuited  or 

•

thrown into fire. Never recharge non-rechargeable batteries. There is a

risk of explosion!

Consult an expert when in doubt about operation, safety or connection of 

•

the device.
Maintenance, modifications and repairs are to be performed exclusively

•

by an expert or at a qualified shop.

If you are not sure about the correct connection or use, or if questions arise which 

are not covered by these operating instructions, please do not hesitate to contact our 

technical support or another qualified specialist.
Voltcraft®, Lindenweg 15, D-92242 Hirschau, Tel. +49 180/586 582 7.

Slide the battery compartment cover at the rear of the product to the right to open 

1. 

the  battery  compartment.  Observe  the  polarity  markings  at  the  bottom  of  the 

battery compartment.
Insert / replace two batteries (type AAA), while observing the correct polarity.

2. 

Close the battery compartment again.

3. 

Replace the batteries when “Lo” appears on the display.

Place the scales on a stable, horizontal and level surface.

1. 

Lift the cover of the scales.

2. 

Press the button ON/OFF to switch the scales on. All display elements will be 

3. 

displayed  for  approx.  six  seconds,  then  the  value  “0.00“  will  be  displayed.  If 

another value is shown, press the button Z/T. The LCD backlight will be turned 

on at the same time.
Press the button MODE to select the unit: grams (g), ounces (oz), carat (ct) or 

4. 

troy ounce (ozt).
Wait until the letter “H” and “o” show on the screen. Place the object to be weighed 

5. 

carefully  on  the  weighing  platform.  The  object’s  weight  will  be  shown  on  the 

display.

Note that when the letter “H” is flashing, the scale is not in a stable status. Wait

until the letter “H” appears steadily before any measurements.

The LCD backlight will be turned off when the scale is idle for 15 seconds. It will be 

6. 

turned on again if any key is being pressed / the weight on the weighing platform 

is changed.
Press the button ON/OFF to switch the scales off. Alternatively, the scales will 

7. 

switch off automatically after idling for approx. two minutes. 

The top of the weighing platform is removable and can be used as a tray. 

The tare function is intended for net measuring using a weighing container. The tare 

function offsets the weight of the weighing container used so that the display shows 

only the net weight of the object to be measured.

Switch on the scale and wait until the display is stabilized.

1. 

Place the empty weighing container (bowl, basket, etc.) on the weighing platform.

2. 

Press the button Z/T and the display shows “0.00” despite of the weighing container 

3. 

resting on the scale.
Put the object to be measured into the weighing container. The display indicates 

4. 

the net weight of the object.