Einhell Mains 3420561 Hoja De Datos

Los códigos de productos

3420561

- 20 -

5. Before starting the equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

Warning!

Always pull the power plug before making

adjustments to the equipment.

The scarifi er is delivered unassembled. The grass

basket and the complete push bar must be as-

sembled and mounted before using the scarifi er.

Follow the operating instructions step-by-step

and use the pictures provided as a visual guide to

easily assemble the machine.

Fitting the rear wheels (see Fig. 3 and Fig. 4)

•

Insert the axles of the rear wheels into the

openings provided (Fig. 3 / Item A).

•

Secure the wheels with the screws provided .

(Fig. 4/ Item 19)

Fitting the push bar brackets (see Figs. 5

and 6)

•

Remove the quick-release lever (Fig. 5/

Item 13) and the washer (Fig. 5/Item 17)

•

Connect the push bar bracket (Fig. 5/Item 7)

to the fastening screw. Make sure that the

curve in the tube (Fig. 6/Item A) is on the out-

side.

•

Now put the washer back on and tighten with

the quick-release lever.

The same tilt angle must be set for both push bar

brackets!

Fitting the lower push bar (see Fig. 7)

•

Slide the lower push bar (Fig. 7/Item 6) onto

the push bar brackets. Do not forget to slip

the stress-relief clip (Fig. 7/Item 4) onto the

tube first.

•

Now join the tubes together using the screws

(Fig. 7/Item 18), washers (Fig. 7/Item 17) and

quick-release levers (Fig. 7/Item 13) supplied.

Fitting the upper push bar (see Fig. 8 to

Fig. 10)

•

Position the upper push bar (Fig. 8 / Item 5)

such that its holes line up with the holes of the

lower bar.

•

Now join the tubes together using the screws

(Fig. 8/Item 18), washers (Fig. 8/Item 17) and

quick-release levers (Fig. 8/Item 13) supplied.

•

Use the cable clips (Fig. 9/Item 12) to attach

the power cable to the tubes of the push bars

so that it is possible to open and shut the

ejector flap (Fig. 10/Item 12).

Please ensure that the ejector fl ap can be opened

and closed easily!

Assembling the grass basket

(see Figs. 11 and -14)

•

Push both frame parts into each other (Fig.

11).

•

Pull the grass basket over the metal frame

(Fig. 12).

•

Pull the rubber clips over the metal frame

(Fig. 13).

•

To hang the grass basket on the scarifier you

must lift the ejector flap (Fig. 14/Item 10) with

one hand and with the other hand take hold of

the grass bag by the handle and hook it onto

the scarifier from above (Fig. 14).

Danger!

Before you ever hook the grass basket to the sca-

rifi er you must ensure that the motor is switched

oﬀ and the cutting unit is not rotating.

Adjusting the handlebar height (see Fig. 15)

Undo the quick-release levers (Fig. 15/Item 13)

on both sides of the scarifi er.

The height of the handlebar can be set to position

1 or 2 (Fig. 15) during operation. You must then

tighten the quick-release fasteners again.

The same tilt angle must be set on both sides.

Adjusting the scarifi er depth (see Fig. 16)

The scarifi er depth is set with the adjustment me-

chanism. Pull the lever in the direction indicated

by the arrow (see Fig. 16) and adjust to the requi-

red position (0/ 1/ 2/ 3). Make sure that the lever

latches in place correctly!

0 = drive/transport position

I = scarifi er depth 3 mm

II = scarifi er depth 6 mm

III = scarifi er depth 9 mm

Electrical connection

The equipment can be connected to any normal

socket with 230V AC. It is only acceptable to con-

nect it to a shockproof socket with a 16A circuit

breaker. Furthermore, a residual-current-operated

protective device with max. 30 mA should be con-

nected upstream.

Anl_GE_SA_1435_SPK7.indb 20

07.08.14 14:33