Medisana BU550 Blood Pressure Monitor 51290 Hoja De Datos
Los códigos de productos
51290
WARNING - BATTERY SAFETY INFORMATION
• Only replace with batteries of the same type, never use different types of
batteries together or used batteries with new ones!
• Insert the batteries correctly, observing the polarity!
• Remove the batteries from the device if it is not going to be used for an
extended period!
• Keep batteries out of children's reach!
• Do not attempt to recharge these batteries! There is a danger of
explosion!
• Do not short circuit! There is a danger of explosion!
• Do not throw into a fire! There is a danger of explosion!
• Do not throw used batteries into the household refuse; put them in a
hazardous waste container or take them to a battery collection point, at
the shop where they were purchased!
batteries together or used batteries with new ones!
• Insert the batteries correctly, observing the polarity!
• Remove the batteries from the device if it is not going to be used for an
extended period!
• Keep batteries out of children's reach!
• Do not attempt to recharge these batteries! There is a danger of
explosion!
• Do not short circuit! There is a danger of explosion!
• Do not throw into a fire! There is a danger of explosion!
• Do not throw used batteries into the household refuse; put them in a
hazardous waste container or take them to a battery collection point, at
the shop where they were purchased!
3.2 Using a Mains Adaptor
Alternatively, you can use the unit with a special mains adaptor (MEDISANA Art.-No.
51013. This connects to the socket provided at the back of the unit. In this case
the batteries remain in the unit. Inserting the connector into the back of the blood pres-
sure monitor switches the batteries off mechanically. It is necessary, therefore, to plug
the mains adaptor into the mains socket first of all and then to connect it to the blood
pressure monitor. If the blood pressure monitor is no longer being used, first remove
the connector from the blood pressure monitor and then pull the mains adaptor out of
the mains socket. Doing this means that the date and time will not have to be reset
each time.
51013. This connects to the socket provided at the back of the unit. In this case
the batteries remain in the unit. Inserting the connector into the back of the blood pres-
sure monitor switches the batteries off mechanically. It is necessary, therefore, to plug
the mains adaptor into the mains socket first of all and then to connect it to the blood
pressure monitor. If the blood pressure monitor is no longer being used, first remove
the connector from the blood pressure monitor and then pull the mains adaptor out of
the mains socket. Doing this means that the date and time will not have to be reset
each time.
1.
2.
3.
4.
5.
3.
4.
5.
6.
3.3 Setting the date and time
Before using the unit, you need to put the LOCK-switch to position "ON" (green).
In "OFF" (red) - position the Bluetooth function is deactivated and all buttons are
locked.
In "OFF" (red) - position the Bluetooth function is deactivated and all buttons are
locked.
i
Press and hold the S-button for at least 3 seconds.
i
Firstly, the date figure starts to flash. Press M-button to adjust the actual month.
Press the S-button to confirm the setting.
Press the S-button to confirm the setting.
i
Now the day figure starts flashing. Proceed accordingly for the input of day, year,
hour and minute (as described under point 3 and 4).
hour and minute (as described under point 3 and 4).
i
On completion of the date and time setting, "Ok" appears on the display. The unit
switches off automatically after about 60 seconds, if no buttons are pressed in order
to save power.
switches off automatically after about 60 seconds, if no buttons are pressed in order
to save power.
3.4 Setting up the user memory
The MEDISANA Upper arm blood pressure monitor BU 550 connect gives you the
opportunity to assign readings to one of two user memories, each of which provides
500 memory slots. Press and hold the M-button for at least 3 seconds, until the
symbol for User 1 appears in the display. By pressing M-button you can switch
User 1 and User 2 or Guest . If you choose "Guest", the values of the reading will
not be saved.
opportunity to assign readings to one of two user memories, each of which provides
500 memory slots. Press and hold the M-button for at least 3 seconds, until the
symbol for User 1 appears in the display. By pressing M-button you can switch
User 1 and User 2 or Guest . If you choose "Guest", the values of the reading will
not be saved.
i
Press the S-button to confirm your selection.
3 Getting started
23
GB