Embedded Artists LPC4088 Developer's Kit EA-OEM-510 EA-OEM-510 Hoja De Datos
Los códigos de productos
EA-OEM-510
LPC4088 Developer’s Kit - User’s Guide
Page 62
Copyright 2013 © Embedded Artists AB
wrong. More symptoms than this is needed to judge if a board is wrong, or not. Do not forget
to press the reset push-button all the time during this measurement. Redo the test in case of
uncertainty.
8. Now, measure the current consumption of the OEM Board when it is running an application. It
is a problem to not have a specified application running because the current consumption can
vary widely between different applications. The current consumption shall increase compared
to the previous test (in case an application is running). It is recommended to download one of
the precompiled sample applications from the LPC4088 Developer’s Kit support page on the
Embedded Artists web site. How to download is explained in next section. The sample
application s_sdram.hex has for example a known current consumption range. The valid
application s_sdram.hex has for example a known current consumption range. The valid
range is 650-900m V (which corresponds to 130-180mA). The current consumption varies
between different sample applications depending on which peripherals that are active. A
running application will in general give a range of 400-700mV (which corresponds to 80-
140mA)
9. In most cases it is possible to power the board via the USB interface, J25 (the UART-to-USB
bridge mini-B USB connector). Redo tests 3) to 8) above again with USB powering. Connect
J25 directly to a PC with the USB cable included in the Developer’s Kit.
Note that not all PC:s and/or laptops can power the board. In such cases, a USB hub with
independent powering can work. In this case, connect J25 to a USB Hub, which in turn is
connected to a PC.
7.2 Contact with OEM Board MCU
The second step is to make sure that the LPC4088 MCU on the OEM Board is working.
Test that it is possible to download one of the precompiled test programs that exist on Embedded
Test that it is possible to download one of the precompiled test programs that exist on Embedded
Artists support site. Use Flash Magic to download code over the UART-to-USB bridge. See section
5.4.1 for details how to download. Make sure both jumpers in JP20 are inserted and that correct
settings in Flash Magic are used.
Optionally test that it is possible to download via the JTAG/SWD interface. A JTAG/SWD debug
interface us then needed. The low-cost LPCXpresso target board series from NXP contains a
Optionally test that it is possible to download via the JTAG/SWD interface. A JTAG/SWD debug
interface us then needed. The low-cost LPCXpresso target board series from NXP contains a
JTAG/SWD debug interface called LPC-LINK that can be used for this. Other brands will also work.
7.3 Using Test Program to Verify Correct Operation
The third step is to utilize the just downloaded precompiled sample applications, one after one, to verify
correct operation of individual parts of the OEM Board as well as the OEM Base Board. While doing
these tests, be sure to not have anything connected to the system.
There are sample applications for testing/verifying operation of:
There are sample applications for testing/verifying operation of:
1. Analog input
2. I2S-E2PROM
3. NAND flash
4. Accelerometer
5. I2S audio via codec
6. Ethernet
7. SD/MMC memory card interface
8. Joystick
9. LEDs and push-buttons (via the PCA9532)
10. Audio via analog output
2. I2S-E2PROM
3. NAND flash
4. Accelerometer
5. I2S audio via codec
6. Ethernet
7. SD/MMC memory card interface
8. Joystick
9. LEDs and push-buttons (via the PCA9532)
10. Audio via analog output