Atmel Evaluation Kit AT91SAM9M10-G45-EK AT91SAM9M10-G45-EK Hoja De Datos
Los códigos de productos
AT91SAM9M10-G45-EK
685
SAM9M10 [DATASHEET]
6355F–ATARM–12-Mar-13
–FC field is programmed with peripheral to memory flow control mode.
–both DST_DSCR and SRC_DSCR are set to 1. (descriptor fetch is disabled)
–DIF and SIF are set with their respective layer ID. If SIF is different from DIF, the DMA Controller is
able to prefetch data and write HSMCI simultaneously.
h.
Program DMAC_CFGx register for channel x with the following field’s values:
–FIFOCFG defines the watermark of the DMA channel FIFO.
–SRC_H2SEL is set to true to enable hardware handshaking on the destination.
–SRC_PER is programmed with the hardware handshaking ID of the targeted HSMCI Host
Controller.
–Enable Channel x writing one to DMAC_CHER[x]. The DMAC is ready and waiting for request.
3.
Wait for XFRDONE in HSMCI_SR register.
35.8.7
WRITE_MULTIPLE_BLOCK
35.8.7.1
One Block per Descriptor
1.
Wait until the current command execution has successfully terminated.
a.
Check that CMDRDY and NOTBUSY are asserted in HSMCI_SR.
2.
Program the block length in the card. This value defines the value
block_length.
3.
Program the block length in the HSMCI configuration register with
block_length
value.
4.
Program HSMCI_DMA register with the following fields:
– OFFSET field with
dma_offset.
– CHKSIZE is user defined.
– DMAEN is set to true to enable DMAC hardware handshaking in the HSMCI. This bit was previously
set to false.
5.
Issue a WRITE_MULTIPLE_BLOCK command.
6.
Program the DMA Controller to use a list of descriptors. Each descriptor transfers one block of data. Block
n
of data is transferred with descriptor LLI(n).
a.
Read the channel Register to choose an available (disabled) channel.
b.
Clear any pending interrupts on the channel from the previous DMAC transfer by reading the
DMAC_EBCISR register.
DMAC_EBCISR register.
c.
Program a List of descriptors.
d.
The LLI(n).DMAC_SADDRx memory location for channel x must be set to the location of the source
data. When the first data location is not word aligned, the two LSB bits define the temporary value
called
data. When the first data location is not word aligned, the two LSB bits define the temporary value
called
dma_offset.
The two LSB bits of LLI(n).DMAC_SADDRx must be set to 0.
e.
The LLI(n).DMAC_DADDRx register for channel x must be set with the starting address of the
HSMCI_FIFO address.
HSMCI_FIFO address.
f.
Program LLI(n).DMAC_CTRLAx register of channel x with the following field’s values:
–DST_WIDTH is set to WORD.
–SRC_WIDTH is set to WORD.
–DCSIZE must be set according to the value of HSMCI_DMA, CHKSIZE field.
–BTSIZE is programmed with
CEILING((block_length + dma_offset)/4).
g.
Program LLI(n).DMAC_CTRLBx register for channel x with the following field’s values:
–DST_INCR is set to INCR.
–SRC_INCR is set to INCR.
–DST_DSCR is set to 0 (fetch operation is enabled for the destination).