Embedded Artists LPC4357 Developer's Kit EA-OEM-511 EA-OEM-511 Hoja De Datos
Los códigos de productos
EA-OEM-511
LPC4357 Developer’s Kit - User’s Guide
Page 61
Copyright 2012 © Embedded Artists AB
7 Troubleshooting
This chapter contains information about how to troubleshoot boards that does not seem to operate
properly. It is strongly advised to read through the list of tests and actions that can be done before
contacting Embedded Artists. The different tests can help determine if there is a problem with the
board, or not. For return policy, please read Embedded Artists’ General Terms and Conditions
document (can be found at
document (can be found at
http://www.embeddedartists.com/shop/
).
7.1 No SWD/JTAG Connection
Note that JP4 must be shorted (jumper installed) in order to enable the JTAG/SWD interface on
the LPC4357.
JP4 might not be inserted by default on the OEM Base Board.
7.2 Powering
The first step is to make sure that powering works properly. The input power interface is described in
section 4.23 .
1. Disconnect the powering and removed the OEM Board, i.e., remove it from the socket (J1).
All other connections to the OEM Base Board shall also be removed.
2. Connect a stable DC supply (+5V, positive center) to J24. Minimum current capability shall be
1A for this test. The noise level should be minimal, less than 50mV.
3. Measure the +5V and +3.3V voltages with the help of the voltage measuring pads on the
OEM Base Board.
Acceptable range for the +5V voltage is 4.5V to 5.5V.
Acceptable range for the +3.3V voltage is +3.2V to +3.4V.
Acceptable range for the +3.3V voltage is +3.2V to +3.4V.
If the reset-LED is dimming instead of being clearly on or off, it is also a sign that the supply
voltages are not stable and outside of valid ranges.
If problem; since the OEM board is disconnected and there is normally no big current
consumption on passive OEM Base Board, it is likely that some part of the OEM Base Board
consumes a lot of current. It might be possible to locate the faulty section/component by
checking component temperatures with the finger tip. Be careful because faulty components
checking component temperatures with the finger tip. Be careful because faulty components
can get very hot.
4. Verify that there are no voltage dips on the supply. A typical indication of this is that the reset-
LED flash from time to time. An oscilloscope can detect voltage dips; measure the supply
voltage in AC mode. Set horizontal resolution to 50mV per square. Set the trigger to normal
mode and adjust the trigger to 50mV below the normal level. That way, the oscilloscope will
mode and adjust the trigger to 50mV below the normal level. That way, the oscilloscope will
trigger every time a voltage dips occurs. By watching the dips it is possible to judge if there is
a problem, or not.
5. Verify that the reset-LED flash when pressing the reset push-button. The LED should also
light shortly after releasing the push button. The extra “LED on time” is very short but still
noticeable (typically a 1/5 of a second, i.e., 200mS).
noticeable (typically a 1/5 of a second, i.e., 200mS).
6. Disconnect the powering and mount the OEM Board again (in J1).
Now, measure the +5V and +3.3V voltages again (see step 2 above). If the +5V voltage is
below acceptable range it is a sign of too weak power supply to the board. If the reset-LED
starts dimming instead of being clearly on or off, it is also a sign of too weak power supply to
the board.
If the reset-LED always light now when the OEM Board is mounted it is a sign of too weak
If the reset-LED always light now when the OEM Board is mounted it is a sign of too weak
power supply or a serious error on the OEM Board. When doing this test, be sure to not have
any SWD/JTAG interface connected or any external source driving the reset signal.
Verify that the reset-LED flash when pressing the reset push-button.
7. In section 4.3 it is described how to measure the current consumption of the OEM Board.
Measure the voltage over J2 while pressing the reset push-button constantly. This will give