Blade 450 X RTF BLH1900M1 Hoja De Datos
Los códigos de productos
BLH1900M1
5
EN
Low Voltage Cutoff (LVC)
The ESC will continuously lower power to the motor until complete shutdown
when the battery reaches 9V under load. This helps prevent over-discharge of the
Li-Po battery. Land immediately when the ESC activates LVC. Continuing to fl y after
LVC can damage the battery, cause a crash or both. Crash damage and batteries
damaged due to over-discharge are not covered under warranty.
when the battery reaches 9V under load. This helps prevent over-discharge of the
Li-Po battery. Land immediately when the ESC activates LVC. Continuing to fl y after
LVC can damage the battery, cause a crash or both. Crash damage and batteries
damaged due to over-discharge are not covered under warranty.
Repeatedly fl ying the helicopter until LVC activates will damage the helicopter
battery.
battery.
Disconnect and remove the Li-Po battery from the aircraft after use to prevent
trickle discharge. During storage, make sure battery charge does not fall below 3V
per cell.
trickle discharge. During storage, make sure battery charge does not fall below 3V
per cell.
Installing the Transmitter Batteries
Transmitter Functions
Replace transmitter batteries when the transmitter beeps and fl ashes a warning
screen.
screen.
2
1
Function
A Antenna
B Throttle Cut
C
Mix/Throttle Hold (Mode 2)
Trainer/Bind (Mode 1)
Trainer/Bind (Mode 1)
D
Rudder Dual Rate (Mode 2)
Gear/Flight Mode (Mode 1)
Gear/Flight Mode (Mode 1)
E Aileron Dual Rate
Function
F
Aileron/Elevator Stick (Mode 2)
Aileron/Throttle Stick (Mode 1)
Aileron/Throttle Stick (Mode 1)
G
Elevator Trim (Mode 2)
Throttle Trim (Mode 1)
Throttle Trim (Mode 1)
H Aileron Trim
I
Roller
J On/Off Switch
Function
K
Charge Port
L Rudder Trim
M
Throttle Trim (Mode 2)
Elevator Trim (Mode 1)
Elevator Trim (Mode 1)
N
Throttle/Rudder Stick (Mode 2)
Elevator/Rudder Stick (Mode 1)
Elevator/Rudder Stick (Mode 1)
O Elevator Dual Rate
Function
P
Gear/Flight Mode (Mode 2)
Rudder Dual Rate (Mode 1)
Rudder Dual Rate (Mode 1)
Q
Trainer/Bind (Mode 2)
Mix/Throttle Hold (Mode 1)
Mix/Throttle Hold (Mode 1)
R
Flap/Gyro
S Trainer Port
T
Battery Cover
The transmitter comes with a thin clear plastic fi lm applied to some front panels
for protection during shipping. Humidity and use may cause this fi lm to come off.
Carefully remove this fi lm as desired.
for protection during shipping. Humidity and use may cause this fi lm to come off.
Carefully remove this fi lm as desired.
For more information on the transmitter, go to www.horizonhobby.com and click on
the support tab for the Spektrum DX6i to download the instruction manual.
the support tab for the Spektrum DX6i to download the instruction manual.
Transmitter Mode Conversion
You can change transmitter modes between Mode 1 and Mode 2. This conversion
requires both a programming and a mechanical change.
requires both a programming and a mechanical change.
Programming set up
1. Power on the transmitter.
2. Press the roller, scroll to Setup List and press the roller to access the Setup
2. Press the roller, scroll to Setup List and press the roller to access the Setup
List.
3. Select Copy/Reset in the Setup List. When the Copy/Reset menu screen opens,
select Reset.
4. Move the Aileron D/R switch forward and backward FOUR TIMES. A screen will
display Mode 1 and Mode 2.
5. Select the desired mode.
6. After you change the transmitter Mode in the Setup List, you will need to make
6. After you change the transmitter Mode in the Setup List, you will need to make
mechanical changes to the transmitter gimbals.
CAUTION: Always power off the transmitter and remove the batteries
before adjusting stick tension or friction straps. Not doing so could result
before adjusting stick tension or friction straps. Not doing so could result
in property damage or injury.
A
D
E
G
J
F
C
B
H
I
S
T
Q
O
N
L
K
P
R
M