Wera LED outdoor free standing light (+ motion detector) 3.84 W Warm white 12537-600 Anthracite 12537-600 Hoja De Datos
Los códigos de productos
12537-600
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
© Copyright 2013 by Conrad Electronic SE.
V1_0713_02-ETS-Mkde
Installation
It is essential that you follow all instructions provided under “Function of the
motion detector” and “Preparing installation”.
1. Use the stand of the product as a template to mark the four drill hole positions through the
screw holes onto the mounting surface.
When drilling or tightening screws, make sure not to damage any cables,
wires or pipes located underneath the surface.
2. Drill the four holes into the mounting surface and insert the dowels into the drill holes.
3. Carefully pull the transparent terminal block box from the lamp casing.
4. Carefully pull the cover from the box.
5. The cover of the terminal block box contains four irregularly sized markings indicating the
3. Carefully pull the transparent terminal block box from the lamp casing.
4. Carefully pull the cover from the box.
5. The cover of the terminal block box contains four irregularly sized markings indicating the
positions for routing the mains cable. Carefully punch a hole in the cover and guide the
mains cable top down through the hole.
Use an appropriate sealing agent (such as silicone) to seal up the hole if it is too
large.
6. Connect the mains cable with the terminal block:
Brown cable = L
Blue cable = N
Green/yellow cable = PE/ground wire, grounding symbol
Blue cable = N
Green/yellow cable = PE/ground wire, grounding symbol
The ground wire must be connected to the terminal block under all
circumstances.
If the product is serving as a replacement for an existing light and there is
If the product is serving as a replacement for an existing light and there is
no ground wire, do not install the product. First install the appropriate supply
leads.
If no ground wire is connected, there will be voltage applied to the metal
If no ground wire is connected, there will be voltage applied to the metal
product housing in the event of an error. This poses a risk of fatal injury due
to electric shock!
Make sure that the cables are not bare for too long as this may cause short-
Make sure that the cables are not bare for too long as this may cause short-
circuiting.
Make sure that all screw connections on both sides of the terminal block
Make sure that all screw connections on both sides of the terminal block
are tight.
7. Put the terminal block and any protruding wires into the terminal block and close the cover.
8. There is an arrow marking on the terminal block box. Insert the box into the lamp housing
8. There is an arrow marking on the terminal block box. Insert the box into the lamp housing
making sure the arrowhead is pointing to the top. The box cover and the wires must point
down accordingly.
9. Align the stand of the product with the dowels and fix the product to the mounting surface
using the four screws.
Make sure that the cables are not squeezed, bent or damaged in any other
way. Do not exert any force when installing the product.
10. Turn on power to the circuit and check to see if the product works.
If the LEDs do not light up, turn off power to the circuit immediately (turn off
circuit breaker and/or automatic fuse).
Then check the connection to the power circuit.
In case of doubt, contact a professional (i.e. an electrician).
Then check the connection to the power circuit.
In case of doubt, contact a professional (i.e. an electrician).
PIR sensor settings
• You may adjust the detection range and operating time at the bottom of the PIR sensor.
• The SENS control for adjusting the detection range is located on the right.
• The TIME control for adjusting the operating time is located on the left.
• Use a flat and slim tool for adjustment, such asa flat head screwdriver.
• The SENS control for adjusting the detection range is located on the right.
• The TIME control for adjusting the operating time is located on the left.
• Use a flat and slim tool for adjustment, such asa flat head screwdriver.
- Turn the control counter-clockwise till the end in order to select the minimum setting.
- Turn the control clockwise till the end in order to select the maximum setting.
- Turn the control clockwise till the end in order to select the maximum setting.
Maintenance and cleaning
Never use aggressive cleaning agents or chemical solutions, as such would
damage the housing (discolorations).
Never point a water jet, for example such of high-pressure cleaning
Never point a water jet, for example such of high-pressure cleaning
equipment, at the lamp, as that could damage the seals!
• Besides occasional cleaning, the device is maintenance-free.
• Turn off the product and let it cool down sufficiently before cleaning.
• Wipe the outer surface with a clean, soft cloth only. In order to remove stubborn staining, you
• Turn off the product and let it cool down sufficiently before cleaning.
• Wipe the outer surface with a clean, soft cloth only. In order to remove stubborn staining, you
may slightly dampen the cloth with warm water.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household
waste.
At the end of its service life, dispose of the product according to the relevant statutory
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage ............................... 220 – 240 V/AC, 50/60 Hz
Power consumption ............................ 4 W (operation) / 0.65 W (standby)
Illuminant ............................................ 48 LEDs (3528 SMD), not dimmable
Colour temperature ............................. 3000 K
Luminous colour ................................. warm-white
Luminous flux ..................................... 230 lm
PIR detection range ............................ 1 m (±0.2 m) – 5 m
PIR detection angle ............................ 90º vertically, 120º horizontally
PIR light sensitivity ............................. 0 – 28 Lux
Operating time .................................... 4 s – 8 min (±1 min)
Protection type .................................... IP54
Protection class .................................. I
Installation height ............................... max. 2 m
Operating / storage conditions ............ -30 to +85 ºC, 0 – 90 % RH (non-condensing)
Dimensions (W x H x D) ..................... 120 x 1000 x 190 mm (item no. 43 24 21)
Power consumption ............................ 4 W (operation) / 0.65 W (standby)
Illuminant ............................................ 48 LEDs (3528 SMD), not dimmable
Colour temperature ............................. 3000 K
Luminous colour ................................. warm-white
Luminous flux ..................................... 230 lm
PIR detection range ............................ 1 m (±0.2 m) – 5 m
PIR detection angle ............................ 90º vertically, 120º horizontally
PIR light sensitivity ............................. 0 – 28 Lux
Operating time .................................... 4 s – 8 min (±1 min)
Protection type .................................... IP54
Protection class .................................. I
Installation height ............................... max. 2 m
Operating / storage conditions ............ -30 to +85 ºC, 0 – 90 % RH (non-condensing)
Dimensions (W x H x D) ..................... 120 x 1000 x 190 mm (item no. 43 24 21)
............................................................
120 x 600 x 190 mm (item no. 43 73 34)
Weight ................................................ approx. 2 kg (item no. 43 24 21)
............................................................
approx. 1.3 kg (item no. 43 73 34)