Panasonic Limit switch 115 Vdc, 250 Vac 5 A Tappet momentary AZ8122CEJ IP64 1 pc(s) AZ8122CEJ Hoja De Datos
Los códigos de productos
AZ8122CEJ
39
.803
±.012
20.4
±0.3
7
∗)
(40)
(Standard type)
Bending radius to be over 100mm 3.937inch
M12 (P=1.25) Panel mounting nut and washed
Wrench groove
M12(P=1.25)
∗)(PT 4max)
PT 1.5max
7
7
(63)
M10 operation adjustment nut
1000
±5
25
mounting holes
2-4.1
2.205
±.012
56
±0.3
cover screw
2-M3
23
cover screw
Operation indicator
M3
6
dia.
+0.2
0
.803
±.012
20.4
±0.3
7.5
±0.2
.295
±.008
1.193
30.3
.594
15.1
(With Neon lamp)
mounting holes
2-M5 (P=0.8) tapped
mounting holes
in depth
2-M5 (P=0.8) tapped
7
7
.276
.157
4
64
2.520
.551
14
.984
.402
10.2
1.102
28
.827
±.008
21
±0.2
15.1
.594
for operation
adjustment
adjustment
.276
(1.575)
(2.480)
.276
39.37
±.197
10.2
.402
4
.157
64
2.520
.551
14
.295
±.008
7.5
±0.2
in depth
2-M5 (P=0.8)
mounting holes
.276
7
2-M5 (P=0.8)
mounting holes
mounting holes
.276
dia. plunger
100 mm 3.937inch and the total bend comes to 360
°
.803
±.012
20.4
±0.3
51.5
PT 30 max
stainless
1.2 dia.
25
100
±1.5
mounting holes
2-4.1
2.205
±.012
56
±0.3
cover screw
2-M3
23
cover screw
Operation indicator
M3
6
dia.
+0.2
0
(Standard type)
.803
±.012
20.4
±0.3
7.5
±0.2
.295
±.008
1.193
30.3
.594
15.1
64
2.520
14
.551
.402
10.2
(With Neon lamp)
4
.157
mounting holes
2-M5 (P=0.8) tapped
mounting holes
in depth
2-M5 (P=0.8) tapped
7
7
.276
.157
4
64
2.520
.551
14
.984
.402
10.2
1.102
28
.827
±.008
21
±0.2
3.937
±.059
15.1
.594
7.5
±0.2
.295
±.008
2.028
steel wire
.047
.047
stainless
steel wire
1.2 dia.
2-M5 (P=0.8)
in depth
mounting holes
7
.276
mounting holes
2-M5 (P=0.8)
Spring wire type
Standard type
General tolerance: ±0.4
±.016
(Should be used with less than 50mm
1.969inch
of T.T.)
Remote wire control type
General tolerance: ±0.4
±.016
1. Mounting
1) Fasten a switch body
2) Fasten a wire tentatively
3) Fasten an actuator
4) Fasten the wire
1) Fasten a switch body
2) Fasten a wire tentatively
3) Fasten an actuator
4) Fasten the wire
Note) When setting the operating position, it is rec-
ommended to adjust operation adjustment nut
to keep safety margin for releasing.
to keep safety margin for releasing.
2. Actuator
1) Make the hole (12.5±0.3mm
1) Make the hole (12.5±0.3mm
.492±.012inch
dia.) on the panel.
2) Fasten the actuator by a panel mount-
ing nut and washer.
3. Remote wire
1) Use the wire in as rectilinear condition
1) Use the wire in as rectilinear condition
as possible.
2) When the wire is bent, the radius
should be more than 100mm
3.937inch
.
3) When fastening the wire, fasten the
wire at the point more than 100mm
3.937inch
as below;
4) Less fastening points are recommended.
5) When the wire is fasten, use the rub-
5) When the wire is fasten, use the rub-
ber bushing to avoid to reform the
diameter.
diameter.
6) When the wire is bent, P.T., M.D. and
O.T. can be adjustable as below;
P.T. = 2.5mm .
098inch
(max.)
M.D. = 1.5mm
.059inch
(max.)
O.T. = 3.5mm
.138inch
(min.)
100mm
100mm
3.937 inch
3.937 inch
Panel thickness max. 10mm
12.5
±0.3 dia.
.492
±.012
.394 inch
VL (AZ8)
04/2005