Idec HE9Z-GP15 Hoja De Datos

HS5D Miniature Interlock Switches

6.4 max.

17.4max.

4.2 to 5.8

ø3.2

A

7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan

Tel: +81-6-6398-2571, Fax: +81-6-6392-9731

E-mail: marketing@idec.co.jp

Specifications and other descriptions in this catalog are subject to change without notice.

Cat. No. EP1285-1 MARCH 2010 5.4S PRINTED IN JAPAN

IDEC ELECTRONICS LIMITED

Tel: +44-1256-321000, Fax: +44-1256-327755

E-mail: sales@uk.idec.com

IDEC ELEKTROTECHNIK GmbH

Tel: +49-40-25 30 54 - 0, Fax: +49-40-25 30 54 - 24

E-mail: service@idec.de

IDEC (SHANGHAI) CORPORATION

Tel: +86-21-5353-1000, Fax: +86-21-5353-1263

E-mail: idec@cn.idec.com

IDEC (BEIJING) CORPORATION

Tel: +86-10-6581-6131, Fax: +86-10-6581-5119

IDEC (SHENZHEN) CORPORATION

Tel: +86-755-8356-2977, Fax: +86-755-8356-2944

IDEC IZUMI (H.K.) CO., LTD.

Tel: +852-2803-8989, Fax: +852-2565-0171

E-mail: info@hk.idec.com

IDEC TAIWAN CORPORATION

Tel: +886-2-2698-3929, Fax: +886-2-2698-3931

E-mail: service@tw.idec.com

IDEC IZUMI ASIA PTE. LTD.

Tel: +65-6746-1155, Fax: +65-6844-5995

E-mail: info@sg.idec.com

www.idec.com

IDEC CORPORATION (USA)

Tel: +1-408-747-0550 / (800) 262-IDEC (4332) 

Fax: +1-408-744-9055 / (800) 635-6246

E-mail: opencontact@idec.com

IDEC CANADA LIMITED

Tel: +1-905-890-8561, Toll Free: (888) 317-4332 

Fax: +1-905-890-8562

E-mail: sales@ca.idec.com

IDEC AUSTRALIA PTY. LTD.

Tel: +61-3-9763-3244, Toll Free: 1800-68-4332

Fax: +61-3-9763-3255

E-mail: sales@au.idec.com

The head of the HS5D can be rotated by removing the 

 

•

four screws from the corners of the HS5D head and rein-

stalling the head in the desired orientation. When reinstall-

ing the head, make sure that no foreign object enters the 

interlock switch. Tighten the screws tightly, because loose 

tightening may cause malfunction.

Recommended screw tightening torque: 0.9 to 1.1 N·m

 

•

Alternative Head Orientations

Factory Setting

Only the NC contact of the main circuit (11-12) turns OFF 

(open) when the head is removed, such as when rotating 

the head. Because NC contacts of other than the main cir-

cuit (11-12) turn ON (closed), be sure to connect the main 

circuit (11-12) to the safety circuit.

Interlock Switch Mounting Screw: 1.8 ± 2.2 N·m 

 

•

 

 

 

 

(two M4 screws) 

Housing Lid Screw: 0.2 to 0.4 N·m (M3 screw)

 

•

Terminal Screw: 

0.6 to 0.8 N·m (M3 screw)

 

•

Connector: 

2.7 to 3.3 N·m 

 

•

Actuators 

 

•

HS9Z-A51: 

 1.8 ± 2.2 N·m (two M4 screws)  

HS9Z-A52: 

 0.8 ± 1.2 N·m (two M4 Phillips screws) 

HS9Z-A51A/A52A:  1.0 to 1.5 N·m (two M4 screws)  

HS9Z-A55: 

 1.0 to 1.5 N·m (two M4 screws)

The above recommended tightening torques of the mount-

 

•

ing screws are the values confirmed with hex socket head 

bolts. When other screws are used and tightened to a 

smaller torque, make sure that the screws do not come 

loose after mounting.

Mounting bolts must be provided by the user.

 

•

To avoid unauthorized or unintended removal of the 

 

•

interlock switch and the actuator, it is recommended that 

the interlock switch and the actuator be installed in an 

unremovable manner, for example using special screws or 

welding the screws.

When using crimping terminals, be sure to install insulation 

tubes on the crimping terminals to prevent electric shocks.

When using stranded wires, make sure that loose wires do 

not cause short circuit. Also do not solder the terminal to 

prevent loose wires.

Recommended manufacturer: JST

Part No.: N0.5-3

Applicable wire size (with insulation tube): 0.2 to 0.5 mm

2

Note:  Do not remove screw A during wiring. Removing the screw 

may cause malfunction or damage.

0.5 to 1.5 mm

2

Use a cable gland with a degree of protection IP67.

30 max.

9 max.

G1/2, PG13.5, M20

Flexible conduit example: VF-03 (made by Nihon Flex)

 

•

Gland Port Size Plastic Cable Gland

Metal Cable Gland

G1/2

—

RLC-103 (Nihon Flex)

PG13.5

—

RBC-103PG13.5 (Nihon Flex)

M20

—

RLC-103EC20 (Nihon Flex)

Gland Port Size

Plastic Cable Gland

Metal Cable Gland

G1/2

SCS-10* (Seiwa Electric)

ALS-16** (Nihon Flex)

PG13.5

ST13.5 (LAPP)

ABS-**PG13.5 (Nihon Flex)

M20

ST-M20X1.5 (LAPP)

ALS-**EC20 (Nihon Flex)

Different cable glands are used depending on the cable 

 

•

sheath diameter. When purchasing a cable gland,         

confirm that the cable gland is applicable to the cable 

sheath diameter.

When using a 1/2-14NPT cable gland, use the HS5D 

 

•

interlock switch with M20 gland port (Type No.: HS5D-

***BM) together with an adaptor (Type No.: MA-M/NPT 

20X1.5 5402-0110, LAPP) and a gasket (Type No.: GP 

M20, LAPP). Install a gasket between the interlock switch 

and the adaptor. Apply sealing tape between the cable 

gland and the adaptor to make sure of IP67 protection for 

the enclosure.

(100405)