Blade BLH7100 Hoja De Datos
12
13
EN
EN
Transmitter Setup Table
Transmitter
"Model
Type"
Transmitter Programming
Switches and Supported Flight Modes
MLP6DSM
N/A
N/A
Ch 5 and 3 flight modes (0, 1, 2)
Flip-Beginner, Invert-Intermediate,
Throttle Cut-Evo: Trigger
DX4e (old)
w/2 Position Switch
N/A
N/A
ACT/AUX and 2 flight modes (0, 2)
Flip-Beginner, Invert-Intermediate,
Throttle Cut-Evo: Trainer
DX5e (old)
w/2 Position Switch
N/A
N/A
Ch 5 and 2 flight modes 0, 2)
Flip-Beginner, Invert-Intermediate,
Throttle Cut-Evo: Trainer
DX4e
w/3 Position Switch
N/A
N/A
Ch 5 and 3 flight modes (0, 1, 2)
Flip-Beginner, Invert-Intermediate,
Throttle Cut-Evo: Trainer
DX5e
w/3 Position Switch
N/A
N/A
Ch 5 and 3 flight modes (0, 1, 2)
Flip-Beginner, Invert-Intermediate,
Throttle Cut-Evo: Trainer
DX6i
Acro
Function List
Flap:125% Up Arrow 125% Down Arrow
Mix 1: Gear to Gear
Rate D 0%, U -125%
SW: GEAR
Mix 2: Gear to Gear
Rate D 0%, U +125%
SW: ELE D/R
Setup List
Reverse: GEAR: R, All others: N
Throttle Cut: Act
GEAR (0) ELE D/R (0) = Beginner
GEAR (1) ELE D/R (0) = Intermediate
GEAR (1) ELE D/R (1) = Evo Mode
Transmitter
"Model
Type"
Transmitter Programming
Switches and Supported Flight Modes
DX7S
Airplane
System Setup
Switch Select
Trainer: Aux1 Flap: Gear
(All others: INH)
Function List
Servo Setup
Reverse
Aux1: R
Throttle Cut Pos: 0% Sw: Mix1
Flap Switch
Pos 0: Beginner
Pos 1: Intermediate
Pos 2: Evo Mode
DX8
Airplane
Servo Setup: Reverse: AUX1-R, All others-N
Switch Select: Trainer: AUX1, F Mode: Gear
Throttle Cut Pos: 0% Sw: Mix1
F MODE and 3 flight modes (0, 1, 2)
DX6, DX9, DX18
Airplane
System Setup
Channel Assign, [NEXT]
Channel Input Config
Gear: B
Aux1: I
Function List
Servo Setup
Reverse
Aux1: R
(All others: N)
ThrottleCut: Pos: -130% Sw: Switch H
B Switch
Pos 0: Beginner
Pos 1: Intermediate
Pos 2: Evo Mode
IMPORTANT: Set up your transmitter before binding your transmitter to the aircraft.
Non-Computerized Transmitter Setup (DX4e and DX5e) Before binding a non-computerized transmitter, ensure all servo reversing is set to
Non-Computerized Transmitter Setup (DX4e and DX5e) Before binding a non-computerized transmitter, ensure all servo reversing is set to
normal and trim is at center.
Computerized Transmitter Setup Start all transmitter programming with a blank ACRO model (do a model reset), then name the model.
Computerized Transmitter Setup Start all transmitter programming with a blank ACRO model (do a model reset), then name the model.
Set Dual Rates to: HIGH 100% LOW 70%.
LED Codes
Equipment
LED Color
LED Status
Operation
Quadcopter
Blue
Rapid Blink
Bind Mode
RTF Transmitter
Red
Blink
Low Rate
Solid
High Rate