Braun 4605 Manual De Usuario
English
Our products are designed to meet the
highest standards of quality, functionality
and design. We hope you enjoy your new
Braun shaver.
highest standards of quality, functionality
and design. We hope you enjoy your new
Braun shaver.
Technical specifications
Wattage via cord set: 4 W, automatic
power supply 220-240 V~ / 50-60 Hz
power supply 220-240 V~ / 50-60 Hz
Description
1 Foil protection cap
2 Shaver foil
3 Cutter block
4 Foil frame
5 Release buttons
6 Long hair trimmer
7 Central switch
8 Low charge light (4615 only)
9 Charging light
2 Shaver foil
3 Cutter block
4 Foil frame
5 Release buttons
6 Long hair trimmer
7 Central switch
8 Low charge light (4615 only)
9 Charging light
10 Shaver socket
11 Mains adapter
11 Mains adapter
Charging the shaver
•
Via the adapter, connect the shaver to
the mains with the motor switched
off. Charge for at least 8 hours (trans-
former and shaver might get warm).
Once the shaver is completely
charged, shave until fully discharged.
Then recharge to full capacity again.
the mains with the motor switched
off. Charge for at least 8 hours (trans-
former and shaver might get warm).
Once the shaver is completely
charged, shave until fully discharged.
Then recharge to full capacity again.
•
A full charge will give up to 25
minutes of cordless shaving time
depending on your beard growth.
However, the maximum battery
capacity will only be reached after
several charging/dis-charging cycles.
minutes of cordless shaving time
depending on your beard growth.
However, the maximum battery
capacity will only be reached after
several charging/dis-charging cycles.
•
Best environmental temperature
range for charging is 15°C to 35°C.
range for charging is 15°C to 35°C.
Indicator lights
•
The green charging light shows that
the shaver is being charged.When the
rechargeable battery is fully charged,
the charging light goes off. If later
the shaver is being charged.When the
rechargeable battery is fully charged,
the charging light goes off. If later
on, the light comes on again, this
indicates that the shaver is being
recharged to maintain its full capa-
city.
indicates that the shaver is being
recharged to maintain its full capa-
city.
•
Model 4615 only: The red low charge
light will come on when the battery
capacity has dropped below 20%,
provided the shaver is switched on.
The remaining capacity will then be
sufficient for 1 to 2 shaves.
light will come on when the battery
capacity has dropped below 20%,
provided the shaver is switched on.
The remaining capacity will then be
sufficient for 1 to 2 shaves.
Shaving
Turn on the shaver («on»)
Trimmer («trim»): When the long hair
trimmer is activated, it allows the
controlled trimming of moustache or
sideburns.
Trimmer («trim»): When the long hair
trimmer is activated, it allows the
controlled trimming of moustache or
sideburns.
Keeping your shaver in top
shape
Cleaning under running water
After each shave, turn on the shaver and
clean it under running hot water.
Occasionally use soap (natural based
liquid soap without particles and
abrasive substances). Then rinse off all
foam and let the shaver run for another
moment.
clean it under running hot water.
Occasionally use soap (natural based
liquid soap without particles and
abrasive substances). Then rinse off all
foam and let the shaver run for another
moment.
Brush cleaning
Instead of cleaning under running water,
you may clean your shaver with a dry
you may clean your shaver with a dry
Tips for the perfect shave
•
We recommend that you shave
before washing, as the skin tends to
be slightly swollen after washing.
before washing, as the skin tends to
be slightly swollen after washing.
•
Hold the shaver at right angles (90°)
to the skin. Stretch your skin and
shave against the direction of beard
growth.
to the skin. Stretch your skin and
shave against the direction of beard
growth.
•
To ensure optimum shaving per-
formance, we recommend to re-
place the shaver foil and cutter
block every 18 months, or when
the parts are worn.
formance, we recommend to re-
place the shaver foil and cutter
block every 18 months, or when
the parts are worn.
5100207_Fix200_KOR Seite 3 Mittwoch, 22. Mai 2002 8:55 08