Behringer DJ Equipment Synthisizer Manual De Usuario

EUROLIGHT LC2412

3. Now pull fader B down and fader A up. The preset appears

at the console output, while the memories dissappear.

4.2.2 Crossfading between memories

There are several ways to crossfade between memories:

Crossfading steplessly using the FLASH keys

Please take the following required steps, as follows:

1. Disengage the CHANNEL FLASH key

;

2. Pull up the CHASE fader

;

3. Press the INSERT key

;

4. Adjust the X-FADE control

to the desired fade in/out

speed;

5. Press the FLASH key (one of the

keys).

The memory is faded in. You determine the illumination level

by using the CHASE and the MAIN fader. To switch to another

memory, simply press another FLASH key. You can alternate

between two memories (the current one and the one selected

before it) by using the STEP key

. You can fade in the current

preset setting instead of the memory by using the PRESET FLASH

key

Faders A and B (

and

) as well as the faders

of the B MEMORY section and the A PRESET section

can be pulled down; in that case, only the memories/

presets activated by means of the FLASH keys are

visible.

If you are currently replaying a chase, it will be

interrupted as soon as you hit the INSERT key. When

you hit the INSERT key for the second time, the chase

resumes.

Manually crossfading between memories using the X-FADER

If you activate the MANUAL key

in addition to the setup

desicribed in chapter 4.2.2, you can then determine the crossfade

times by switching from memory to memory using the X-FADE

fader.

1. Select a memory using a FLASH key.
2. Now, move the X-FADE fader to an end position, and the

memory will be faded in.

If you select no new memory, you can alternate

between the two most recently used memories

back and forth.

Fading memories out

To fade memories out, release the INSERT key

. If you pull

the X-FADE fader in the same direction while having faded in a

memory right before that, the memory is faded out only when

you pull the control down again. Renewed pulling the control

upwards, no memory is displayed.

Activating a chase and interrupting it by pressing

the INSERT key fades in the next CHASE step when

you pull the X-FADE fader upward. To fade out, you

have to first select a chase that contains no steps

(see chapter 6.2).

When you let go of the MANUAL key, using the STEP key

lets you fade out withing the time set up using the X-FADE fader.

When a chase is active, and you interrupt it by

pressing the INSERT key, pressing the STEP key

fades the next chase step in.

4.2.3 Crossfading between memories

of different banks

You can change your current storage bank by selecting a

new bank using the UP/DOWN keys. The memory activated

previously remains on the stage unti you pull the fader to zero.

The LEDs of the UP/DOWN keys flash in case there are active

memories belonging to the abandoned bank. Pull up a memory

fader, and the memory stored at this location in the new storage

bank is activated.

The memories that were activated before you

changed the bank remain visible on the stage until

you pull the fader down into its zero position. This

way, you can see multiple memories on the stage

(and the respective control lights).

4.3 Preset flash and memory flash

4.3.1 Preset flash

This key activates the flash function for the A PRESET section.

If the solo function is not active, PRESET FLASH adds a lighting

configuration (set up in the A PRESET section) to an active memory

(fader A

at zero). When the solo function is active, pulled

up memories are switched off.
Configuration:

Memory mode, memory fader

raised

Fader A

closed, MAIN fader

raised

Fade in the preset configuration using PRESET FLASH. The A

PRESET fader and the MAIN fader determine the illumination level.
With solo function: memories are deactivated.

4.3.2 Memory flash

The memory flash function can be activated to abruptly

implement stored presets (memories) into an active preset,

instead of smoothly fading it in using a fader.

No memory can be recalled in preset mode.

Additionally, the memory flash function can not

be executed.

Configuration:

Memory mode, memory fader

raised,

Fader A raised, fader B closed or partially raised, MAIN fader

raised.
Fade in the pulled up memories using the MEMORY FLASH. The

B MEMORY fader and the MAIN fader determine the illumination

level.
With solo function: The preset is deactivated.

4.4 Programming memories

without direct control (blind)

In addition to programming memories by using the preview

function (see chapter 4.1.3), you can also program memories

using yet another method, without being visible on the stage.

Make sure that the LIVE key

is not active. The fader A also

has to be in its zero position.

After having pressed the MEMORY key

in the programming

section, select a storage bank by using the UP/DOWN keys and

a memory by using the FLASH key, and edit it by using the faders

from the A PRESET section. The fader configurations are only

indicated by means of control lights on the FLASH keys.

Please confirm your changes by hitting the SOFT A (preset) or

SOFT B (all) keys and then edit another memory, or quit by hitting

QUIT.

4. THE B MEMORY SECTION