Behringer Powerlight PL2000 Manual De Usuario
4
POWERLIGHT PL2000 User Manual
1. Introduction
Thank you for the confidence you have shown in us by purchasing the
POWERLIGHT PL2000. It is an extremely dependable, premium-
featured rack light in the 19" format. The POWERLIGHT offers you
many mains connectors and the highest possible safety for maximum
flexibility on the stage or at the studio.
POWERLIGHT PL2000. It is an extremely dependable, premium-
featured rack light in the 19" format. The POWERLIGHT offers you
many mains connectors and the highest possible safety for maximum
flexibility on the stage or at the studio.
2. Control Elements
(2) (1)
(3)
Front-side control elements
(1)
Use the POWER switch to power up the POWERLIGHT PL2000.
The POWER switch should always be in its “Off” position
whenever you connect the unit to the mains.
The POWER switch should always be in its “Off” position
whenever you connect the unit to the mains.
◊
Merely pressing the POWER switch does not disconnect the
unit fully from the mains. To fully disconnect the unit from
the mains, unplug the power cord from the power outlet.
During the installation, make sure that both the power cord
and the power outlet function properly. When not using the
unit for prolonged periods of time, please unplug the unit’s
power cord from the power outlet.
unit fully from the mains. To fully disconnect the unit from
the mains, unplug the power cord from the power outlet.
During the installation, make sure that both the power cord
and the power outlet function properly. When not using the
unit for prolonged periods of time, please unplug the unit’s
power cord from the power outlet.
◊
Please make sure that the unit is grounded at all times.
For your own protection, you should never tamper with
the grounding of the cable or the unit itself. The unit must
be connected to the mains with an intact ground wire at
all times.
For your own protection, you should never tamper with
the grounding of the cable or the unit itself. The unit must
be connected to the mains with an intact ground wire at
all times.
(2)
The LIGHT switch activates the rack lighting. The light can also
be turned on independent of the POWER switch.
be turned on independent of the POWER switch.
(3)
The rack light can be rotated and can be individually adjusted to
best suit your lighting needs.
best suit your lighting needs.
(4)
(6)
(7)
(5)
Control elements in the back
(4)
There are 8 mains connectors in the back of the PL2000 for
providing power to additional equipment in your rack. The total
power load of the equipment connected to the PL2000 may not
exceed 8 A.
providing power to additional equipment in your rack. The total
power load of the equipment connected to the PL2000 may not
exceed 8 A.
(5)
The mains connection is made with a standard IEC receptacle.
A matching power cord is included.
A matching power cord is included.
(6)
Your rack light’s fuse holder is located here. Blown fuses should
only be replaced with fuses of the same type and rating.
only be replaced with fuses of the same type and rating.
(7)
This is your PL2000’s automatic circuit breaker. If the total load
of the equipment you have connected to the PL2000 exceeds
8 A, the circuit breaker engages and completely turns the
PL2000 off. If this happens, remove one or more of the units you
have connected in order to lower the overall load below 8 A.
After approx. 2 minutes the automatic circuit breaker is reset
and your PL2000 can be turned on again. If the circuit breaker
engages again, disconnect additional equipment.
of the equipment you have connected to the PL2000 exceeds
8 A, the circuit breaker engages and completely turns the
PL2000 off. If this happens, remove one or more of the units you
have connected in order to lower the overall load below 8 A.
After approx. 2 minutes the automatic circuit breaker is reset
and your PL2000 can be turned on again. If the circuit breaker
engages again, disconnect additional equipment.