White Rodgers 1F95-1291 Emerson Blue 12" Humidity Touchscreen Programmable Thermostat Instruccion De Instalación

White-Rodgers is a business 
of Emerson Electric Co.

The Emerson logo is a  
trademark and service mark 
of Emerson Electric Co.

1. Blown fuse or tripped circuit breaker. 

2. Furnace power switch to OFF. 

3. Furnace blower compartment door or 

  panel loose or not properly installed. 

4. Loose connection to thermostat or system.

Replace fuse or reset breaker. 

Turn switch to ON. 

Replace door panel in proper position to engage safety 

interlock or door switch. 

Tighten connections.

1. Pilot light not lit. 

2. Furnace Lock-Out Condition. Heat 

  may also be intermittent. 

 

 

3. Heating system requires service or 

  thermostat requires replacement. 

Re-light pilot. 

Many furnaces have safety devices that shut down when 

a lock-out condition occurs. If the heat works intermittently 

contact the furnace manufacturer or local HVAC service 

person for assistance. 

Diagnostic: Set SYSTEM Switch to HEAT and raise the 

setpoint above room temperature. Within a few seconds 

the thermostat should make a soft click sound. This sound 

usually indicates the thermostat is operating properly. If 

the thermostat does not click, try the reset operation listed 

above. If the thermostat does not click after being reset 

contact your heating and cooling service person or place 

of purchase for a replacement. If the thermostat clicks, 

contact the furnace manufacturer or a HVAC service 

person to verify the heating is operating correctly.

1. Cooling system requires service or 

  thermostat requires replacement.

Same as diagnostic for No Heat condition except set the 

thermostat to 

COOL and lower the setpoint below the 

room temperature. There may be up to a five minute delay 

before the thermostat clicks in Cooling.

1. Possible short in wiring. 

2. Possible short in thermostat. 

3. Possible short in heat/cool/fan system. 

4. FAN Switch set to Fan 

ON.

Check each wire connection to verify they are not shorted 

or touching together. No bare wire should stick out from 

under terminal block. Try resetting the thermostat as de-

scribed above. If the condition persists the manufacturer 

of your system or service person can instruct you on how 

to test the Heat/Cool system for correct operation. If the 

system operates correctly, replace the thermostat.

1. Thermostat thermometer setting 

  requires adjustment.

The thermometer can be adjusted +/- 4 degrees. See 

Temperature Display Adjustment in the Configuration 

Menu section.

temperature swing) 

1. The location of the thermostat and/or 

  the size of the Heating System may 

  be influencing the cycle rate.

Digital thermostats provide precise control and cycle 

faster than older mechanical models. The system turns 

on and off more frequently but runs for a shorter time 

so there is no increase in energy use. If you would like 

an increased cycle time, choose 

SL for slow cycle in the 

Configuration menu, step 7 (heat) or 8 (cool). If an ac-

ceptable cycle rate is not achieved, contact a local HVAC 

service person for additional suggestions. 

Press the menu 

key

 (

key

 will disappear) and hold in for 

20 seconds. This unlocks the thermostat.

1. Voltage Spike or static discharge

Use the Reset Operation shown above.

1. Earlier version of thermostat

To access the earlier version instruction sheet (37-6914E) 

go to www.white-rodgers.com, enter 1F95-1291 in Model 

Number Search 

Reset Operation
Note: If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the 
thermostat by removing the thermostat from the wall plate and removing batteries for 2 minutes. After two minutes, replace 
the batteries and replace thermostat on wall plate. If the thermostat has been reset and still does not function correctly contact 
your heating/cooling service person or place of purchase.