Behringer V-TONE GMX110 Manual De Usuario

V-TONE GMX110/GMX210/GMX212/GMX1200H

6. INSTALLATION

You determine the input volume of the effect module by

using MIDI controller #7. This lets you adjust the volume of your

V-TONE to your own requirements. Since this controller does

not control master volume, you should first adjust the maximum

volume you need by using the master volume control, and then

use MIDI controller #7 to lower the volume. This function is also

called volume controller.

The operating range of the Wah effect is adjusted using MIDI

controller #15.

Furthermore, if youre using LFO-controlled modulation effects,

you can deactivate LFO and implement modulation via MIDI

controller #15. To activate this MIDI controller, you should first

set up the LFO velocity either directly on your V-TONE or set the

respective MIDI controller to value 0.

Of course, you can use a MIDI sequencer or a computer-

based MIDI editor for MIDI remote control, particularly in the home

recording environment.

5. TUNER

The integrated tuner is activated by pressing the CHANNEL

key for about 2 seconds (directly on the amp or on the

footswitch).

5.1 Tuning your guitar

The chromatic tuner automatically recognizes the frequencies

of guitar notes. For A string, this means a frequency of 110 Hz.

When you connect your guitar to the V-TONE and strum a string,

the tuner tries to recognize the tone and shows it in the display.

Because the tuner functions chromatically, it can also recognize

semitones. These are shown in the display with a b

accompanying the value.

However, it may be the case that a played note (shown in the

display as for example a) slightly deviates from the ideal tone.

This will be indicated by lighting up at least one of the red tuner

LEDs (HIGH/LOW) near the FX display. The faster the LED blinks,

the harsher the deviation of the played tone from the note shown

in the display. If the middle LED (green) lights up, the tone you

played is completely in tune with the tone indicated in the display.

When the tuner is active, the loudspeaker outputs are typically

muted. However, sometimes it is preferable not to mute the signal

in order to let you have acoustic control of what you are doing

while you are tuning your guitar. For this reason, the V-TONE

has an integrated tuner level function.
s

You can adjust tuner volume from 0 to 99 by using the FX

control. At 0 the guitar signal is completely muted. After a

successfully implemented adjustment, the display auto-

matically goes back to tuner mode.

5.2 Setting up the a reference tone

To put complete freedom at your disposal when tuning your

instrument, you have the option to change the preset of the

reference tone a. Here is a quick intro to the subject.

The so-called chamber tone a has been continually revised

upwards ever since it was first measured: tuning forks of Bach,

Handel or Mozart were at 415, 420 or 421 Hz (vibrations pro

second).

Nowadays, orchestras set the a with 444 Hz, and the Berlin

Philharmonic Orchestra wishes to stay ahead: their chamber

tone a lies at a full 447 Hz.

The reference tone a of the V-TONE is programmed at

440 Hz. Lets say, you want to work with a big orchestra that

works with the chamber tone a set to 444 Hz. To activate the

function that changes the chamber tone, do the following:

Activate the tuner by keeping the CHANNEL key pressed

for a few seconds.

By turning the PRESET control, you can adjust the a

reference tone up or down in 1 Hz increments for a maximum

of 15 Hz. The last two digits of the frequency value are

always shown in the display, since the first digit is always

a 4. For example, when you start with the 440 Hz basic

tone, and then press the right arrow key four times, the

display shows 44, which corresponds to a frequency of

444 Hz.

After about 5 seconds, the display goes back to tuner mode.

Your changes are automatically stored. Ideal tones for the

remaining strings are automatically set up using the newly

adjusted frequency as a reference.

A quick hit on the CHANNEL key lets you leave tuner mode and

go back to amp mode.

6. INSTALLATION

6.1 Audio connections

With the exception of the headphone output and the AUX input

(stereo jacks), audio inputs and outputs of your BEHRINGER

V-TONE are provided in the form of mono jack connectors. Tape

inputs and outputs are provided as RCA connectors.

Please keep in mind that your V-TONE should be

installed and operated only by those who possess

sufficient technical knowledge about its installation

and operation. Everyone dealing with your V-TONE

should be sufficiently grounded both during the

installation as well as during actual usage. Failure

to do so may cause undesirable or faulty operation

due to electromagnetic discharges and similar.