Behringer Ultrapar UP1200 Guía De Instalación Rápida
(EN)
Controls
ULTRAPAR UP1200 Controls
Lamp
The halogen lamp needed for using the
UP1200 is not included with the shipment.
To start using your ULTRAPAR spotlight,
use the BEHRINGER 575H (575 Watts at
110 V/230 V) or any other compatible
lamp with the G9.5 socket. Make sure
that the lamp you use is compatible with
local voltage.
The halogen lamp needed for using the
UP1200 is not included with the shipment.
To start using your ULTRAPAR spotlight,
use the BEHRINGER 575H (575 Watts at
110 V/230 V) or any other compatible
lamp with the G9.5 socket. Make sure
that the lamp you use is compatible with
local voltage.
Disassembling the Lamp Casing/
Installing a Lamp
Installing a Lamp
Lamps that have been damaged, must be
replaced immediately! Please proceed as
follows to replace the lamp:
• Disconnect the spotlight from the mains
replaced immediately! Please proceed as
follows to replace the lamp:
• Disconnect the spotlight from the mains
power supply, and unscrew the thumb
screw on the rear of the lamp casing (3)
(G 9.5 socket)
• Carefully pull out the lamp casing
(3)
from the rear part of the spotlight
• Carefully take the lamp out of its carton,
by holding it at its socket
• Depending on socket type, use the
corresponding temperature-resistant
rubber adapter provided
• Press the lamp socket (and the rubber
adapter) into the holder inside the
lamp casing (3) until the lamp is safely
mounted in place. The entire bottom side
of the lamp socket must be in contact
with the casing
• Remount the casing and connect it to the
grounding cable (2) coming from the
spotlight. Fasten the thumb screw until
the casing is safely mounted in place
• Avoid touching the reflector with bare
hands. Oily finger marks can bake onto
the glass surface and substantially lower
optical quality
Lenses
Your ULTRAPAR spotlight is delivered with
four glass lenses.
four glass lenses.
◊ Never use your ULTRAPAR without
the protective mesh in combination
with the color frame because it
prevents direct contact with the
hot lamp surface. It also prevents
pieces of broken glass from
uncontrollably dispersing in the
event of the lens being broken.
with the color frame because it
prevents direct contact with the
hot lamp surface. It also prevents
pieces of broken glass from
uncontrollably dispersing in the
event of the lens being broken.
The shape of each lens determines the
light beam produced by the spotlight.
Also, use the turnable lens ring to optimally
adjust the direction of the light beam.
light beam produced by the spotlight.
Also, use the turnable lens ring to optimally
adjust the direction of the light beam.
Dismounting the Lens
• Disconnect the spotlight from the mains
• Disconnect the spotlight from the mains
and wait until it has cooled down
• Place the spotlight on a flat and
stable surface. Never mount or dismount
the lens, while the spotlight is fixed to a
truss or stand
• Remove the protective mesh (8):
press its two spring shackles, then pull
out the mesh
• Directly in front of the lens, you will find
a movable metal clamp (4) attached
to the lens ring (5). Turn the lens ring,
until the metal clamp is located on the
top side of the spotlight (directly below
the locking bracket (13)
• Tilt the front side of the spotlight
forward by at least 45°
• Push the movable metal clamp upward
to dismount and pull out the lens (10)
Mounting the Lens
• Tilt the spotlight forward and turn the
• Tilt the spotlight forward and turn the
lens ring (5), until the movable metal
clamp (4) is located on the top side of
the spotlight (directly below the locking
bracket (13)
• Insert the lens with its rounded side
towards the rear. The lower edge of
the lens must be located behind the
projecting elements (6) of the lens ring
• Press the upper edge of the lens slightly
towards the rear, until it locks in behind
the metal clamp (4)
• Installation of the protective mesh (8):
Press the two spring shackles of the
protective mesh and place it directly
in front of the lens ring (5). There are
two slots in the die-cast casing of
your ULTRAPAR for the “feet” of the
protective mesh. The two spring
shackles must be located directly below
the locking bracket (13)
Color Frame
The color frame (11) is used to hold color
filters. Please observe the following
instructions to install the color frame:
• Detach the locking bracket (13) on the
filters. Please observe the following
instructions to install the color frame:
• Detach the locking bracket (13) on the
top side of the spotlight, by pushing it to
the side. Then, open the bracket and tilt
it towards the rear
• Insert the color frame into the frame
holders (9) and (12), i.e. the outer
guiding rail (with stops on three sides)
on the front side of the ULTRAPAR
• Push the locking bracket (13) to the side
and move it down until it locks in
◊ Only use color filters
with appropriate
temperature resistance!
temperature resistance!
◊ Never use your ULTRAPAR without
the protective mesh in combination
with the colorframe because it
prevents direct contact with the hot
lamp surface. It also prevents pieces
of broken glass from uncontrollably
dispersing in the event of the lens
being broken.
with the colorframe because it
prevents direct contact with the hot
lamp surface. It also prevents pieces
of broken glass from uncontrollably
dispersing in the event of the lens
being broken.
Cleaning the Reflector
• Disconnect the spotlight from the mains
• Disconnect the spotlight from the mains
and remove the lamp casing.
• Remove the color frame (11),
the protective mesh and lens (10),
so that the reflector is easily accessible
• Cleaning the reflector: Use oil-free
compressed air or a soft, lint-free
cotton cloth. Tenacious stains can
be removed by adding some mild
soap water, however, don’t forget to
remove all soap water remnants as well
• Remount the spotlight
◊ Never clean the reflector with
◊ Never clean the reflector with
commercial window cleaners,
as the chemical substances
contained in these agents can
damage the reflector insert!
as the chemical substances
contained in these agents can
damage the reflector insert!
◊ Don’t use paper towels or other
material with a rough surface to
wipe the refl ector clean, so as
to avoid scratches damaging the
reflector surface.
wipe the refl ector clean, so as
to avoid scratches damaging the
reflector surface.
◊ Avoid touching the reflector with
bare hands. Oily finger marks can
bake onto the glass surface and
substantially lower optical quality.
bake onto the glass surface and
substantially lower optical quality.
Suspended Installation
Use the mounting bracket (1) to attach
your spotlight to a stand or truss.
Always use M12 steel screws to fasten the
spotlight. Your UP1200 must be secured
with an additional safety steel cable .
Use the steel cable fixed to the spotlight
casing (eyelet (15)).
your spotlight to a stand or truss.
Always use M12 steel screws to fasten the
spotlight. Your UP1200 must be secured
with an additional safety steel cable .
Use the steel cable fixed to the spotlight
casing (eyelet (15)).
Once the spotlight has been adjusted,
it must be secured in place with the
locking screw (14).
it must be secured in place with the
locking screw (14).
Check Out behringer.com for
Full Manual
Name
Quality
Properties
Narrow-spot lens
Transparent glass
Round beam (15°)
Spot lens
Grain screen glass
Round, slightly diffuse beam (19°)
Medium flood lens
Glass with few facets
Oblong beam (21° x 34°)
Wide medium flood lens Glass with many facets
Oblong beam (30° x 51°)
ULTRAPAR lenses and their features
10 ULTRAPAR UP1200
11
Quick Start Guide