White Rodgers 1F78-144 White-Rodgers 70 Series Non-Programmable Single Stage Thermostat Instruccion De Instalación
Failure to follow and read all instructions carefully
before installing or operating this control could cause
personal injury and/or property damage
before installing or operating this control could cause
personal injury and/or property damage
Installation Instructions for
Heating & Air Conditioning
1F78
Non-Programmable Thermostat
CONTENTS
Preparations .................................................. 1
Thermostat Details ........................................ 1
Removing Old Thermostat ............................. 1
Mounting and Wiring ...................................... 2
Check Thermostat Operation ......................... 3
Specifications ................................................ 5
Troubleshooting ............................................. 5
Thermostat Details ........................................ 1
Removing Old Thermostat ............................. 1
Mounting and Wiring ...................................... 2
Check Thermostat Operation ......................... 3
Specifications ................................................ 5
Troubleshooting ............................................. 5
YOUR THERMOSTAT REPLACES
Typical System Compatibility Chart
1F78
Standard Heat Only Two Wire Gas or Oil Fired Systems (24 volt)
Yes
Electronic Ignition Heat Only Two Wire Systems (24 volt)
Yes
Electronic Ignition Heat Only Gas or Oil Fired Systems (24 volt)
Yes
Standard Heat/Cool Systems (24 volt)
Yes
Heat/Cool Systems Electric Heat (24 volt)
Yes
Heat Only Electric Heat Systems (24 volt)
Yes
Cool Only Systems (24 volt)
Yes
Heat Pump Systems (No Aux or Emergency Heat)
Yes
Hot Water Zone Heat Only (Two Wire) Systems
Yes
Hot Water Zone Heat Only (Three Wire) Systems
No
Line Voltage Heating or Baseboard 110/240 Volt Systems
No
Millivolt Systems Floor or Wall Furnaces
Yes
12 VDC Mobile Home Application
Yes
Multistage Systems
No
Systems Exceding 30VAC, 1.5 Amp
No
2
THERMOSTAT DETAILS
Mounting
hole
Mounting
hole
W904
Clip for
Celsius
Display
W905 Clip
for Hydronic
System
Electric/Gas
Switch
W
RH
B
RC
G
O
Y
+
-
+
-
GAS
ELEC
W904
W905
Figure 1. Thermostat
NOTE: Earlier models refer to 37-7006 for jumper locations.
HAND OR POWER
DRILL WITH 3/16 INCH
DRILL BIT, IF NEEDED
DRILL WITH 3/16 INCH
DRILL BIT, IF NEEDED
FLAT BLADE SCREWDRIVER
WIRE CUTTER/STRIPPER
1
PREPARATIONS
To prevent electrical shock and/or equipment damage,
disconnect electrical power to the system at the main fuse
or circuit breaker until installation is complete.
disconnect electrical power to the system at the main fuse
or circuit breaker until installation is complete.
CAUTION
!
Before removing wires from old thermostat’s switching subbase,
label each wire with the terminal designation it was removed
from.
label each wire with the terminal designation it was removed
from.
1.
Remove Old Thermostat: A standard heat/cool thermostat
consists of three basic parts:
a. The cover, which may be either a snap-on or hinge type.
b. The base, which is removed by loosening all captive screws.
c. The switching subbase, which is removed by unscrewing
the mounting screws that hold it on the wall or adaptor plate.
2.
Shut off electricity at the main fuse box until installation is
complete. Ensure that electrical power is disconnected.
3.
Remove the front cover of the old thermostat. With wires still
attached, remove wall plate from the wall. If the old thermostat
has a wall mounting plate, remove the thermostat and the wall
mounting plate as an assembly.
has a wall mounting plate, remove the thermostat and the wall
mounting plate as an assembly.
4.
Identify each wire attached to the old thermostat using the
labels enclosed with the new thermostat.
5.
Disconnect the wires from the old thermostat one at a time. DO
NOT LET WIRES FALL BACK INTO THE WALL.
6.
Install new thermostat using the following procedures.
PART NO. 37-6615C
Replaces 37-6615B
1028
Assemble tools required below.
3
REMOVING OLD THERMOSTAT
www.white-rodgers.com
www.emersonclimate.com