Bradford-White Corp Water Heater BMT2H Manual De Usuario

Page 12

SIZE

DISTANCE FROM GAS METER

AND

OR LAST STAGE REGULATOR

GAS TYPE

1½"

2"

2"

1"

1½"

1½"

2"

2"

2½"

1½"

1½"

2"

2"

2½"

3"

1½"

2"

2½"

2½"

2½"

3"

2"

2"

2½"

2½"

3"

3"

2"

2½"

2½"

2½"

3"

3"

2"

2½"

2½"

3"

3"

3½"

2½"

2½"

3"

SIZE

DISTANCE FROM GAS METER

AND

OR LAST STAGE REGULATOR

GAS TYPE

 NOTES: 1. These figures are based on 1/2" (0.12kPa) water column

pressure drop.

2. Check supply pressure and local code requirements

before proceeding with work.

3. Pipe fittings must be considered when determining gas

pipe sizing.

5.

Test for spillage at the draft hood relief opening
after 5 minutes of main burner operation. Use the
flame of a match or candle, or smoke from a
cigarette, cigar or pipe.

6.

After it has been determined that each appliance
remaining connected to the common venting system
properly vents when tested as outlined above,
return doors, windows, exhaust fans, fireplace
dampers and any other gas burning appliance to
their previous conditions of use.

7.

Any improper operation of the common venting
system should be corrected so that the installation
conforms to the National Fuel Gas Code, ANSI
Z223.1/NFPA 54 and/or CSA B149.1, Installation
Codes. When resizing any portion of the common
venting system, the common venting system should
be resized to approach the minimum size as
determined using the appropriate tables in Part II of
the National Fuel Gas Code, ANSI Z223.1/NFPA
54 and/or CSA B149.1, Installation Codes.

For outdoor applications, the vent and combustion

air openings must be covered with proper terminals to
prevent rain, snow and other objects from falling into the
Brute Deluxe.

If local codes allow, outdoor installations may use

1' of appropriately sized galvanized single wall or B-
Vent and a rain cap for exhaust vent termination in the
default configuration (venting out of the top). Note that
some local codes may require a higher vertical vent
height, extending above any perimeter fencing, etc. In
installations where the appearance of the vent is
objectionable, the low profile vent terminals in 

Table 6

may be used.

Combustion air inlets consist of appropriately sized

galvanized pipe and elbows to allow the open end to
face down aside the boiler. This is available as a
Commercial Kit from the manufacturer.

Part numbers for the low profile terminals to cover the

vent and combustion air openings are shown in Table 6.

Gas piping should be supported by suitable

hangers or floor stands, not by the appliance.

Brute Deluxe’s gas train allows the user to pipe the

gas from either the right side or the left side of the unit.
As shipped, the right side of the gas train is capped off,
and there is a manual valve on the left side. If desired,
the manual valve on the left side of the gas train may be
moved to the right side, and the cap on the right side
may be moved to the left.

Review the following instructions before

proceeding with the installation.
1.

Verify that the appliance is fitted for the proper
type of gas by checking the rating plate. Brute

OUTDOOR VENT

OUTDOOR

SIZE

TERMINAL

COMBUSTION

AIR TERMINAL

500

20254703

D2007900

750

20254705

D2007900

1000

20254705

D2008000

1250

D2007700

D2008000

1500

D2007700

D2008000

1750

D2007800

D2008000

2000

D2007800

D2008200