White Rodgers 1F83-51 Guía De Operación

2

1. Shut off electricity at the main fuse box until installation is

complete. Ensure that electrical power is disconnected.

2. Remove the front cover of the old thermostat. With wires

still attached, remove wall plate from the wall. If the old
thermostat has a wall mounting plate, remove the thermostat
and the wall mounting plate as an assembly.

3. Identify each wire attached to the old thermostat using the

4. Disconnect the wires from old thermostat one at a time. DO

5. Install new thermostat using the following procedures.

1. Remove the packing material from the thermostat.

2. This thermostat is configured from the factory to operate a

heat/cool, fossil fuel (gas, oil, etc.), forced air system with up
to 2 stages of heat and 2 stages of cool. It is configured
correctly for any system that DOES NOT require the thermo-
stat to energize the fan on a call for heat.

If your system is an electric heat or heat-pump system that
REQUIRES the thermostat to turn on the fan on a call for
heat, locate the GAS/ELECTRIC switch on the back of the
thermostat (see fig. 1) and switch it to the ELECTRIC
position. This will allow the thermostat to energize the fan
immediately on a call for heat. If you are unsure if the heating/
cooling system requires the thermostat to control the fan,
contact a qualified heating and air conditioning service
person.

3. A jumper is located on the back of the thermostat, so that you

may customize the thermostat to meet your individual pref-
erence (see fig. 1). In most applications, the factory jumper
setting provides the most comfortable and convenient ther-
mostat operation.

Jumper wire W901 determines how fast the system cycles
on and off, based on temperature change. As shipped from
the factory, the thermostat will maintain a very consistent
room temperature, usually within 1

°

F of the thermostat

setting. To achieve a slower on and off cycle, providing a
slightly wider temperature span, cut and separate jumper
wire W901.

This thermostat requires 3 “AA” alkaline batteries to operate.
Batteries are installed in the thermostat at the factory with a
battery tag to prevent power drainage. You must remove the
battery tag to engage the batteries and provide power to the
thermostat. After batteries are engaged, thermostat display and
features may be viewed before installing thermostat.

If LOW BATTERY is displayed, the batteries are low and should
be replaced with fresh “AA” Energizer

®

 alkaline batteries. To

replace batteries, install the batteries along the top of the base
(see fig. 2). The batteries must be installed with the positive (+)
ends to the left.

1. Gently remove the cover by pulling it straight off the base.

Forcing or prying on the unit may cause damage to the unit.

2. Pull wires through the hole in the thermostat base and place

the base over the hole in the wall. Mark mounting hole
locations on the wall using the base as a template.

3. Move the base out of the way. Drill mounting holes.

4. Fasten the base loosely to the wall, as shown in fig. 2, using

two mounting screws. Place a level against the bottom of the
base, adjust until level, and then tighten the screws. (Level-
ing is for appearance only and will not affect thermostat
operation.) If you are using existing mounting holes, or if the
holes drilled are too large and do not allow you to tighten the
base snugly, use plastic screw anchors to secure the base.

5. Check that the SYSTEM switch is in the OFF position.

Connect the wires beneath the terminal screws on the base
using the appropriate wiring diagram (see figs. 3 through 5).

6. Push excess wire into wall and plug hole with a fire-resistant

material (such as fiberglass insulation) to prevent drafts from
affecting thermostat operation.

(Instructions continue on page 4.)

W901
CUT FOR
LONGER CYCLES

GAS   ELECTRIC

Mounting

holes

Reset

button

Screw anchors

Alkaline batteries (3 “AA”–

install “+” ends to the left)

C

W2

R

G

Y

Y2

W