White Rodgers 1F82-261 Manual De Usuario

1. Blown fuse or tripped circuit breaker.

Replace fuse or reset breaker.

2. Furnace power switch to OFF.

Turn switch to ON.

3. Furnace blower compartment door or

Replace door panel in proper position to engage

panel loose or not properly installed.

safety interlock or door switch.

1. System Switch not set to Heat.

Set System Switch to Heat and raise setpoint
above room temperature.

2. Loose connection to thermostat or system.

Verify thermostat and system wires are securely
attached.

3. Heating System requires service or

Diagonistic: Set System Switch to Heat and raise

thermostat requires replacement.

the setpoint above room temperature. Within a five
minutes the thermostat should make a soft click
sound. This sound usually indicates the thermostat
is operating properly. If the thermostat  does not
click, try the reset operation listed above. If the
thermostat does not click after being reset contact
your heating and cooling service person or place
of purchase for a replacement. If the thermostat
clicks, contact the furnace manufacturer or a
service person to verify the heating system is
operating correctly.

1. System Switch not set to Cool.

Set System Switch to Cool and lower setpoint
below room temperature.

2. Loose connection to thermostat or system.

Verify thermostat and system wires are securely
attached.

3. Cooling System requires service or thermostat

Same procedure as diagnostic for No Heat

requires replacement.

condition except set the thermostat to Cool and
lower the setpoint below the room temperature.
There may be up to a five minute delay before
the thermostat clicks in Cooling if the compressor
lock-out option is selected in the configuration
menu (Item 7).

1. Possible short in wiring.

Check each wire connection to verify they are

2. Possible short in thermostat.

not shorted or touching together. No bare wire

3. Possible short in Heat/Cool/Fan system.

should stick out from under terminal screws. Try

4. Fan Switch set to Fan On.

resetting the thermostat as described below.
If the condition persists, the manufacturer of
your system or service person can instruct you
on how to test the Heat/Cool system for correct
operation. If the system operates correctly,
replace the thermostat.

1. The location of the thermostat and/or the size

Item 2 in the Configuration Menu is the adjustment

of the Heating System may be influencing the

that controls the cycle rate. If an acceptable cycle

cycle rate.

rate is not achieved using the FA  (Fast) or SL
(Slow) adjustment contact a local service person for
additional suggestions.

1. The location of the thermostat and/or the size

The cycle rate for cooling is fixed and can not be

of the Cooling System may be influencing the

adjusted. Contact a local service person for

 cycle rate.

suggestions.

1. Thermostat thermometer setting requires

The thermometer can be adjusted +/- 4 degrees as

 adjustment.

listed in item 8 of the Configuration Menu. No other
adjustment is possible.

1. Loss of power to thermostat.

The thermostat will maintain its program in memory
even with no power but the clock time will be
incorrect when power is restored. See No
Heat/No Cool/No Fan  (common problems) above
for items to check in the system.

1. EMR activated

See Configuration Menu (Item 5).

1. AM or PM set incorrectly in program.

Check current clock and program settings including

2. AM or PM set incorrectly on the clock.

the AM or PM designations for each time period.

3. Voltage spike or static discharge.

If a voltage spike or static discharge occurs use the
Reset Operation listed above.

1. Voltage Spike or Static Discharge.

If a voltage spike or static discharge occurs use the

Reset Operation listed above.

If a voltage spike or static discharge blanks out the display or
causes erratic thermostat operation you can reset the thermo-

stat by pressing the reset button (see Fig 1). If the thermostat
has power, has been reset and still does not function correctly
contact your heating/cooling service person or place of pur-
chase.