World Marketing of America KWN195 Manual De Usuario

12

n

n

   WARNING:  If  you  do  not  follow

these  instructions exactly,  a fire or
explosion  may  result   causing
property   damage,  personal  injury  or
loss   of   life.

A.   When  lighting  the  pilot,  follow
these  instructions  exactly.
B.     BEFORE  LIGHTING  smell  all
around  the  appliance  area  for  gas.
Be  sure  to  smell  next  to  the  floor
because  some  gas  is  heavier  than
air  and  will settle on  the  floor.

l  

Do   not    try   to   light  any

         appliance.

l 

  Do    not    touch    any    electric

switch;  do  not  use any   phone

         in your building.

l 

 Immediately   call    your   gas

supplier   from  a   neighbor’s
p h o n e .     F o l l o w     t h e     g a s

         supplier’s  instructions.

l 

 if  you  cannot  reach  your gas

supplier,         call        the         fire

         department.
C.      Use  only   your  hand  to  push in
or  turn  the  gas  control  knob.
Never  use  tools.  If  the  knob  will
not  push  in  or  turn  by  hand,  don’t
try  to  repair  it , call  a  qualified
service  technician  or  gas  supplier.
Force  or  attempted  repair  may
result  in  a  fire  or  explosion.
D.     Do  not  use  this  appliance  if
any  part  has  been  under  water.
Immediately  call  a  qualified  service
t e c h n i c i a n     t o     i n s p e c t     t h e
appliance  and  to  replace  any  part of
the  control  system  and  any gas
control  which  has  been   under   water.

n

n

1.     STOP!      Read        the      safety

information on the side  of  heater.

2.     Make  sure  equipment  shutoff
        valve  is  fully  open.
3.      Turn  control  knob  clockwise 
         to  the  OFF  position.
4.      Wait   five(5)  minutes   to   clear

out any gas. Then smell for gas,
including  near  the floor. If you
smell gas, STOP! Follow "B" in the
safety  information on  the side  of
heater.  If  you  don’t  smell

         gas, go to  the  next  step.
5.      Turn  control  knob counterclock-

wise  

   to  the  PILOT position.

Press  in  control  knob  for  five(5)
s e c o n d s .   ( s e e   F i g u r e   1 9 ) .

         

  You   may    be    running

this  heater  for  the  first  time
after  hooking  up  to  gas  supply.
If  so,  the  control  knob  may
need  to  be  pressed  in  for  30
seconds. This  will  allow  air  to

         bleed  from the  gas  system.
        

l 

If  control  knob  does  not

pop  up  when  released, contact
a  qualified  service  person  or

         gas supplier  for  repairs.
6.      With   control   knob  pressed   in,

push  down  and  release  ignitor
button. This  will  light   pilot. The
pilot  is  attached  to  the  front  of
burner. If  needed, keep pressing
ignitor  button  until  pilot  lights.

: If  pilot  does not  stay  lit, refer

to  

Troubleshooting

,  pages 14 through

16. Also  contact  a  qualified  service
person   or  gas  supplier  for  repairs.
Until  repairs  are  made, light   pilot  with
match.To  light  pilot   with  match, see

Manual  Lighting  Procedure

.

7.       Keep     control      knob     pressed

in  for  30 seconds after lighting
pilot. After  30  seconds,  release

        control  knob.

    l 

If   control  knob  does  not

pop  up  when  released, contact

n

n

1.      Turn   control   knob  clockwise
        to  the  OFF  position.
2.     Turn  off  all  electric  power  to  the

appliance  if  service  is  to

         be  performed.

Shutting  Off  Burner  Only  (pilot
stays  lit )
Turn  control   knob  clockwise  
to  the  PILOT  position.

a  qualified  service  person  or

         gas supplier  for  repairs.

: If  pilot  goes  out,repeat

steps 3  through  7.This  heater
has  a  safety  interlock  system.
Wa i t     o n e ( 1 ) m i n u t e   b e f o r e

         lighting  pilot  again.
8.    Turn           control          knob

counterclockwise

to  desired

heating  level. The  main  burner
should  light. Set  control  knob  to
any  heat  level  between  HI  and

        LO.(see  Figure  19)

    CAUTION:  Do  not  try  to

adjust  heating  levels  by  using  the
equipment  shutoff  valve.