Manualsbrain.com
  1. Manuales
  2. Marcas
  3. Superchips Inc.
  4. Car Stereo System 1715 maz
  5. Manual De Usuario

Superchips Inc. Car Stereo System 1715 maz Manual De Usuario

Descargar
Página de 8
 
 
Page 9 of 16
  
Form 0129L 03/29/07                                                                                            
 Superchips Inc
.
 
Superchips Inc.  
1790 East Airport Blvd., Sanford, FL. 32773  (407) 585-7000  http://www.Superchips.com 
Superchip & Superchips are registered trademarks of Superchips, Inc. 
 
 
 
 
Once a shift pressure has been changed, the message displayed will be: 
 
SHIFT PRESS. n-n  
 MIN----------MAX
   
(n-n is 1-2, 2-3 or 3-4) 
 
The present Shift Pressure setting will flash. The vehicle program determines the MAX 
setting. MIN is the vehicle’s stock setting. Use ‘<’ to lower the Shift Pressure, ‘>’ to raise the 
Shift Pressure. Press ‘>’ while MAX is flashing to select the Superchips Performance 
Program setting. Press ‘YES’ to save the Shift Pressure Custom Option setting. The MAX 
MicroTuner will repeat this process for each Shift Pressure. 
 
Editing the Speed Limiter Option Setting
 
The Speed Limiter option allows the user to set the vehicle Speed Limiter to: 
• Use 
the 
Superchips Performance Program raised setting. 
• 
Use the STOCK setting. 
 
The MAX MicroTuner will beep and display the message: 
 
SPEED LIMITER  
Raise  or  Stock
 
 
 
 
The current Speed Limiter setting will flash. Use ‘<’ or ‘>’ to change the setting and ‘YES’ to 
save the Speed Limiter Custom Option setting.
  
 
Editing the Tire Height Option Setting 
The Tire Height Option allows the user to correct the Speedometer/Odometer when other 
than stock tires are installed. The Tire Height Option allows the user to set the Tire Height 
to STOCK or 24.0 - 38.0 inches in 1/4-inch intervals. Tire height should be measured from 
the top of the tire at its highest point to the ground. 
 
The MAX MicroTuner will beep and display the message: 
 
TIRE Height:    
     xx.xx
       
 
The present Tire Height setting is displayed. Use ‘<’ or ‘>’ to change the Tire Height setting 
and ‘YES’ to save the Tire Height Custom Option setting. The STOCK tire size setting is 
selected by pressing ‘<’ when the 24.00 tire height is displayed. 
 
Note: The Tire Height Option is NOT supported for all vehicles. 
 
Editing the Gear Size Option Setting 
The Gear Size Option allows the MAX Tuner to match the transmission Shift Points to the 
selected Gear Size. It also corrects the Speedometer/Odometer when other than STOCK 
Gears are installed. The Gear Size Option allows you to set the Gear Size to STOCK or 
one of the following options: 
 
2.73, 3.08, 3.27, 3.31, 3.55, 3.73, 4.10, 4.56 
 
Note: The Gear Size Option is NOT supported for all vehicles. 
 
The MAX MicroTuner will beep and display the message: 
 
Set GEAR Size:    
xxx
       (xxx is Stock or the Gear Size) 
 
The present Gear Size setting flashes. Use ‘<’ or ‘>’ to change the Gear Size setting and 
‘YES’ to save the Gear Size Custom Option setting. Pressing ‘<’ key when the lowest gear 
ratio is displayed will select the STOCK gear setting. 
 
 
Page 10 of 16
  
Form 0129L 03/29/07                                                                                            
 Superchips Inc
.
 
Superchips Inc.  
1790 East Airport Blvd., Sanford, FL. 32773  (407) 585-7000  http://www.Superchips.com 
Superchip & Superchips are registered trademarks of Superchips, Inc. 
 
 
 
 
7. Viewing the Option Settings 
The MAX MicroTuner will beep and display the message: 
 
 
View Custom Opts?  
 YES or NO 
 
Press ‘YES’ to view the present values of the Custom Option Settings. Press any key on 
the MAX MicroTuner keypad. The Custom Options current settings will be presented in 
order.  Press any key to view the next Custom Option setting. 
 
Press ‘NO’ to continue without viewing the Custom Option Settings.  
The MAX MicroTuner will beep and display the message: 
 
Accept Custom  
Opts? YES or NO 
 
Press ‘YES’ on the MAX MicroTuner keypad to continue with the tuning process. 
Press ‘NO’ to start over at Installing the Superchips Performance Program at Step 5. 
 
  Install TUNING?   
YES or NO     
 
Press ‘YES’ on the MAX MicroTuner keypad to continue with the tuning process. 
Press ‘NO’ to start over at Selecting Tune Vehicle / Diagnostics at Step 2. 
 
8. Programming Section 
The MAX MicroTuner will beep and display the message: 
 
Turn Ignition    
OFF  Press >  
 
Turn the ignition to the OFF position and press the ‘>’ key on the keypad.  The MAX 
MicroTuner will beep and blink the following message for approximately 6 seconds: 
 
Initialization..     
Please Wait…  
 
After initialization is complete, the MAX MicroTuner will beep and display the message: 
 
Turn Ignition ON  
Do NOT START Eng
 
 
Turn the ignition switch ON. The MAX MicroTuner will beep once and display the following 
messages: 
Ready to Install  
then 
Do NOT turn OFF
 
New TUNING  
 
the IGNITION!!! 
 
then 
 
Press >           
to Continue… 
 
 
Press ‘>’. The MAX MicroTuner will beep once and erase the present program.  The MAX 
MicroTuner will blink the following message: 
 
Erasing Present  
Program...   
IMPORTANT NOTE 
Do not interrupt the MAX MicroTuner programming cycle or disconnect it from your 
vehicle until the programming cycle is complete. The entire programming cycle can take 
several minutes.