Harbor Freight Tools 93920 Manual De Usuario
Page 14
SKU 93920
for technical questions, please call 1-800-444-3353.
Orient the assembled door frames for so that the Outer Door Frame (27a) is on the
left, and the Inner Door Frame (27b) is on the right. This is the assembly used for
the left door, the right door will be assembled later with the Outer and Inner Door
Frames on the opposite sides (outer on right, inner on left). All illustrations show
the left door assembly.
left, and the Inner Door Frame (27b) is on the right. This is the assembly used for
the left door, the right door will be assembled later with the Outer and Inner Door
Frames on the opposite sides (outer on right, inner on left). All illustrations show
the left door assembly.
Attach the Top Door Frame (30) to the top of the Outer/Inner Door
Frames (27a, 27b). Make sure that the rounded portion faces
the front and that the flange where the pane will sit faces down
towards the center of the door, see the diagram to the right.
Frames (27a, 27b). Make sure that the rounded portion faces
the front and that the flange where the pane will sit faces down
towards the center of the door, see the diagram to the right.
Using two Short Bolts (59) and two Nuts (61), attach the Door
Slider (29) to the Top Door Frame (30) with the rollers on the top
of the door.
Slider (29) to the Top Door Frame (30) with the rollers on the top
of the door.
Insert a Door Bottom Slider (64) into each end of the Bottom Door
Frame (32). Make sure that the Sliders are assembled the correct
way, with the gap facing the back of the door – see diagram to
the right. Attach the Bottom Door Frame (32) to the Outer/Inner
Door Frames (27a, 27b) using two Screws (57) on each side – the
one on the top into the Bottom Door Frame (32) and the bottom
one into the Door Bottom Slider (64).
Frame (32). Make sure that the Sliders are assembled the correct
way, with the gap facing the back of the door – see diagram to
the right. Attach the Bottom Door Frame (32) to the Outer/Inner
Door Frames (27a, 27b) using two Screws (57) on each side – the
one on the top into the Bottom Door Frame (32) and the bottom
one into the Door Bottom Slider (64).
Raise the assembled Door up and insert the first roller of its Door
Slider (29) onto the Door Rail (28). Carefully align the first Bottom
Door Slider (64) over the edge of the Front Floor Plate (17) – see
illustration to the right. Carefully slide the door over and align the
other top Roller and bottom Slider as you did the first ones.
Slider (29) onto the Door Rail (28). Carefully align the first Bottom
Door Slider (64) over the edge of the Front Floor Plate (17) – see
illustration to the right. Carefully slide the door over and align the
other top Roller and bottom Slider as you did the first ones.
Assemble and install the right door by following the preceding
steps, except place the Outer and Inner Door Frames (27a, 27b) on the opposite
sides as explained in step 3.
steps, except place the Outer and Inner Door Frames (27a, 27b) on the opposite
sides as explained in step 3.
Once both doors are installed, install a Short Bolt (59) and Nut (61) into the hole
on the ends the Door Rail (28) to prevent the doors from sliding off the rails. Attach
the Right and Left Rail End Caps (70,71) onto the ends of the Door Rails.
on the ends the Door Rail (28) to prevent the doors from sliding off the rails. Attach
the Right and Left Rail End Caps (70,71) onto the ends of the Door Rails.
3.
4.
5.
6.
7.
8.
9.
27a
30
pANE
27a
30
pANE
27b
32
64
57
27b
32
64
57