Manualsbrain.com
  1. Manuales
  2. Marcas
  3. Chamberlain
  4. Remote Light Switch
  5. Manual De Usuario

Chamberlain Remote Light Switch Manual De Usuario

Descargar
Página de 8
BEFORE YOU BEGIN:
This device REQUIRES a ground; if a ground is not available, contact a 
qualified electrician. If you are not experienced and familiar with electrical 
wiring and electrical codes, contact a qualified electrician. Some codes 
require installation by a qualified electrician. Install in accordance with all 
national and local codes. Ensure the existing switch and light is working 
prior to installing the new switch.
1.  Disconnect power at the circuit breaker or fuse box BEFORE 
proceeding. 
2. Remove the wall plate and set aside for re-assembly. 
REMOVE OLD WALL SWITCH:
1. Remove switch from switch box.
2. During removal, identify or label the load and line wires.
   NOTE: Typically a line wire is the incoming hot wire from the circuit 
breaker. The load wire is the wire supplying power between the switch 
and the light. 
3. Keep all load wires separated from line wires.
INSTALL NEW SWITCH (Figure 1):
1. Identify the antenna routing (Figure 1).
2.  Connect the wires (Figure 2). NOTE: If your wiring includes a neutral 
wire this wire is not required, combine neutral wire(s) and cap with 
wire nut (not provided).
  •  Green wire to ground.
       Connect the green wire on the new switch to the exposed copper 
ground, green wire, or to the ground connection within metal 
switch box. NOTE: If ground doesn’t exist contact an electrician 
to add a ground. This product will not function without a proper 
ground.
  •  Red wire to load.
  •  Black wire to line.
3.  Secure connections with a wire nut and wrap each wire nut with 
electrical tape.
   NOTE: Turn all wire nuts clockwise, making sure the bare wires are 
covered. Tug on each wire nut to make sure the connections are good.
4.  Carefully pack the wiring back into switch box. Make sure the wires are 
not pinched or strained. Make sure the antenna is hanging straight 
down between the switch box and the drywall.
5.  Fasten the remote light switch to the switch box with the screws 
(provided).
6.  Fasten the wall plate securely over the switch box with the original 
screws from the wall plate.
TEST
1. Turn on the power to circuit at fuse box or circuit breaker.
2.  Test the light switch, manually press the light switch to ensure the 
light is functional (Figure 3). If it is not functional, see 
Troubleshooting.
INSTALLATION 
Figure 3
Black Wire
Line
Red Wire
Load
Green Wire
Ground
To prevent possible SERIOUS INJURY or DEATH from electrocution or 
fire:
•   Turn off power at the fuse box or circuit breaker BEFORE 
proceeding. 
•  The light control is ONLY for indoor use.
•   Installation and wiring MUST be in compliance with ALL local 
electrical and building codes.
Switch 
Box
Load
Light
Line
Circuit Breaker 
or Fuse Box
Black 
Wire
Red 
Wire
Line 
Wire
Neutral
Load 
Wire
Load
Remote 
Light Switch
Ground 
Wires
Neutral 
Wires
Ground
Screws
Figure 1 
For optimal 
range fully 
extend the 
antenna. Feed 
antenna wire 
between a gap 
between the 
switch box 
and drywall.
Wall Plate
(existing-not provided)
Screws 
(not provided)
Green 
Wire
Inside 
of cable
Yellow 
Antenna
2
IMPORTANT NOTE: This illustration is ONLY an example and your 
application and wiring may be different.
Press the switch to the 
ON position. The light 
should turn on.
Press the switch to the 
OFF position. The light 
should turn off.
Figure 2