Multiquip Sander SFCS-16 Manual De Usuario

 

 

 

The MULTIQUIP SFCS16 FLOOR COVERING 
SCRAPER is shipped from the factory secured on a 
specially designed wooden pallet  and protected from 
external damage by a corrugated carton or wood 
crate. If shipped with a corrugated carton, the Surface 
Grinder is secured to the pallet with wood support 
strips. Remove the carton or crate immediately upon 
receipt using suitable tools to remove the nails. 
 
REMOVING THE FLOOR COVERING SCRAPER 
FROM THE PALLET. 
 
Tools Required: 
 
1 each, cutting type pliers. 
1 each, claw hammer or a hammer and an appropriate 
pry bar. 
 
Remove the corrugated carton which is fastened to the 
pallet. The FLOOR COVERING SCRAPER is secured 
to the pallet with banding. Using the pliers, cut and 
remove the banding. The FLOOR COVERING 
SCRAPER can then be removed from the pallet. 
 
 
 
 
WEAR SAFETY GLASSES AND OTHER 
APPROPRIATE SAFETY APPAREL WHEN 
CUTTING THE BANDING AND/OR REMOVING THE 
CORRUGATED/WOOD SHIPPING CRATE. 
 
Included in the shipment should be the following: 
 
1 each, FLOOR COVERING SCRAPER main frame 
assembly. 
1 each, extension cord with integral GFI. 
1 each, adjustable section of the operator handle. 
1 each, pack of standard blades. 
 
The FLOOR COVERING SCRAPER is shipped from 
the factory  completely assembled with the exception 
of the adjustable section of the operator handle. If 
ordered with the Surface Grinder, optional blades and 
accessories can be shipped separately or included in 
the shipping container. 
 
Visually inspect the shipment for freight damage 
and/or missing parts. If shipping damage is evident, 
contact the delivering carrier immediately to arrange 
for  an inspection of the damage by its claims 
representative. Federal law requires that  a claim be 
filed within a specific time period. If missing parts  are 
detected, notify your dealer or the Customer Service 
Department who will assist you in obtaining them. 

Check  all fasteners for proper security. Consult a 
fastener torque chart for the proper torque value if any 
fastener is found to require retorquing. 
 
INSTALLATION OF THE ADJUSTABLE SECTION 
OF THE OPERATOR HANDLE. 
 
The installation of the adjustable section of the 
operator will require a level working surface of 
sufficient size and appropriate height. 
 
1) The FLOOR COVERING SCRAPER incorporates 
an operator handle design that folds for transport  and 
storage. The handle is secured to the main frame  at 
two locations;  a pivoting (fixed) location secured by 
Allen head type capscrews  and  a retaining (locking) 
location secured by removeable, ball-detent type pins. 
The pins are secured to the main frame by lanyards.  
 
2) To place the operator handle in the work position, 
move the handle upright so that the ball-detent pins 
can be inserted through the operator handle and main 
frame. Determine the ball-detent pins are properly 
inserted through the operator handle  and main frame 
to fully expose the ball detent. FIGURE 1. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FIGURE 1 
 

THE BALL DETENT MUST BE FULLY EXPOSED 
AGAINST THE MAIN FRAME TO PROVIDE THE 
PROPER PIN RETAINING FORCE. AN IMPROPER 
PIN RETAINING CONFIGURATION CAN RESULT IN 
UNEXPECTED OPERATOR HANDLE MOVEMENT. 
THIS OCCURRENCE CAN RESULT IN PROPERTY 
DAMAGE AND/OR PERSONAL INJURY. 
 
3) Remove the threaded knobs from the fixed section 
of the operator handle. Install the adjustable section 
into the fixed section with the handle grips facing