Maxus MXN064 Manual De Usuario

The MXN064 is
equipped with an
adjustable direc-
tion exhaust
deflector. This is
intended to allow the user to change
the direction of the exhaust. Simply
twist the deflector to any direction
desired.

1. Disconnect the

air supply from
the nailer.

2. Remove all

nails from the
magazine (see
Loading/
Unloading).
Failure to do so will cause the nails
to eject from the front of the tool.

3. Undo latch by

pulling out and
down. The wire
latch will disen-
gage from the
hooks on the nose.

4. The door can

now be rotat-
ed, exposing
the jammed
fastener.

5. Remove the

jammed fasten-
er, using pliers
or a screwdriv-
er if required.

6

Rotate door
back into the
closed position.

7. Extend the wire

latch and place
over the hooks
on the nose.

8. Close the latch

by pushing the
latch up and in
until the latch
snaps into
place. 

9. Make sure the

trigger and
work contact
element (WCE)
move freely up
and down without sticking or bind-
ing.

Please call our Nailer Hotline at 1-888-
241-5858 with any questions regarding
the operation or repair of this nailer or
for additional copies of this manual.

Only qualified personnel shall repair
the tool and they shall use genuine
Maxus replacement parts and acces-
sories, or parts and accessories which
perform equivalently.

When repairing a nailer, the internal
parts must be cleaned and lubricated.
Parker O-lube or equivalent must be
used on all o-rings. Each o-ring must be
coated with O-lube before assembling.
A small amount of oil must be used on
all moving surfaces and pivots. 

Operating Instructions

movement

Rotate

This mode
requires the trigger to be pulled each
time a nail is driven. The nailer can be
actuated by depressing the WCE
against the work surface followed by
pulling the trigger. 

The trigger must be released to reset
the tool before another nail can be dri-
ven.

1. Disconnect the

air supply from
the nailer.

2. Remove all

nails from the
magazine (see
Loading/
Unloading).

3. Make sure the trigger and work

contact element (WCE) move freely
up and down without sticking or
binding.

3. Do not load with the safety or trig-

ger depressed.

4. Always unload all fasteners before

removing tool from service.
Unloading is the reverse of loading,
except always disconnect the air
hose before unloading.

The MXN064 is equipped with an
adjustable depth of drive feature. This
allows the user to determine how deep
a fastener will be driven into the work
surface.

1. Adjust operating pressure so nails

are driven consistently. Do not
exceed 110 psi.

2. To drive the nail shallower, turn the

wheel (C) to right to the extent
desired.

3. To sink a nail deeper, turn the

wheel (C) to left to the extent
desired.

4. Make sure trigger

and work contact ele-
ment (WCE) move
freely up and down
without binding or
sticking after each adjustment.

4. Reconnect air

supply to the
nailer.

5. Depress the

Work Contact
Element (WCE)
against the
work surface
without pulling the trigger. The
nailer MUST NOT OPERATE. Do not
use the tool if it operates without
pulling the trigger. Personal injury
may result.

6. Remove the

nailer from the
work surface.
The Work
Contact
Element (WCE) must return to its
original down position. The nailer
MUST NOT OPERATE. Do not use
the tool if it operates while lifted
from the work surface. Personal
injury may result.

7. Pull the trig-

ger and
depress the
work contact
element
(WCE) against the work surface. The
nailer MUST NOT OPERATE.

8. Depress the

Work Contact
Element
(WCE) against
the work sur-
face. Pull the trigger. The nailer
MUST OPERATE.

1. Always connect the tool to the air

supply before loading fasteners.

2. Pull pusher (B) back until the nail

follower falls behind the nails. Insert
strip of nails into rear of magazine
(A).

Operating Instructions

1

1

2

1

2

CAMPBELL

CAMPBELL

PROFESSIONAL

PROFESSIONAL

HAUSFELD

HAUSFELD

movement

(B)

(A)

(C)