Honeywell Galaxy 3-48C Instruccion De Instalación
Galaxy 3 Series Installation Manual
2-3
On-board
RIOs/ Smart PSUs/EN51 PSU
Keypads
Keyprox
MAX
Galaxy Panel
Zones
Outputs
Poss.
Address
Zones
Outputs
Poss.
Address
Poss.
Address
Poss.
520 (line 1)
(lines 2, 3, 4)
16
8
15
16
16
1 - 9, A - F
0 - 9, A - F
0 - 9, A - F
120
384
384
60
64
64
8
8
8
0 - 2, B, C, D, E, F
0 - 6, F
0 - 6, F
3
7
7
0-2
0-6
0-6
8
8
8
Figure 2-3. Galaxy 3-520 System Configuration
G3-520 Configuration
Galaxy 3-520
Line
Line
Line
Line
1
2
3
4
Keypads (8)
CP027/
Keyprox (3)
CP028
Keyprox (3)
CP028
Max (8)
MX03
MX03
Keypads (8)
CP027/
Keyprox (7)
CP028
CP027/
Keyprox (7)
CP028
8 zones
4 outputs
RIO (15)
C072
C072
8 zones
4 outputs
OR
8 zones
4 outputs
8 zones
4 outputs
Smart PSU (16)
P015
P015
RIO (16)
C072
C072
Twisted Pair
Screened Cable
W002
Screened Cable
W002
Cable run 1 km (max)
Cable run 1 km (max)
Lines 2, 3 and 4 have the same configuration
RF RIO Module (16)
C076
C076
Certain keypad and
max addresses can
be replaced by a
combined keyprox unit.
max addresses can
be replaced by a
combined keyprox unit.
*
*
*
*
*
NOTE:
Valid addresses for the
keyprox are:
Line 1 (0, 1 & 2).
Lines 2, 3 & 4 (0-6).
This sets the address for both
the keypad and card reader
parts of the keyprox.
Valid addresses for the
keyprox are:
Line 1 (0, 1 & 2).
Lines 2, 3 & 4 (0-6).
This sets the address for both
the keypad and card reader
parts of the keyprox.
16 zones on board
8 outputs
on board
on board
on board
telecom
area
telecom
area
Max (8)
MX03
MX03
OR
OR
OR
OR
OR
NOTE:
RIOs, RF RIO's and
PSU's can be mixed on
the lines. The maximum
number of combined
modules is given in the
table below.
RIOs, RF RIO's and
PSU's can be mixed on
the lines. The maximum
number of combined
modules is given in the
table below.
*
RS232
Serial Port
Serial Port
PSTN
8 zones
4 outputs
Power Unit (16) P025
or
Power RIO (16) P026
or
Power RIO (16) P026
Smart PSU (15)
P015
P015
8 zones
4 outputs
RF RIO Module (15)
C076
C076
Power Unit (15) P025
or
Power RIO (15) P026
or
Power RIO (15) P026
Printer Interface (1)
A134/A161
A134/A161
ISDN Module (1)
E077 (comm 3)
E077 (comm 3)
RS232 Module (1)
E054 (comm 2)
E054 (comm 2)
Telecom Module (1)
E062 (comm 5)
E062 (comm 5)
Ethernet Module (1)
E080 (comm 4)
E080 (comm 4)
Output Module (4)
C078
C078
4 - 16 outputs
Output Module (4) C078
NOTE: Each Output Module can simulate
up to 4 RIO's (outputs only) depending
on DIP switch setting.
Valid addresses for the Output Module are
the same as standard RIO's.
up to 4 RIO's (outputs only) depending
on DIP switch setting.
Valid addresses for the Output Module are
the same as standard RIO's.
4 - 16 outputs
NOTE:
The Telecom, Printer Interface,
RS232, Ethernet and ISDN
modules can only be
connected to line 1.
If a Telecom module is attached,
keypad address E cannot be
connected to line 1(address E is
shown as 18 on the system).
If an RS232 module is attached,
keypad address D cannot be
connected to line 1 (address D is
shown as 17 on the system).
If an Ethernet module is attached,
keypad address B cannot be
connected to line 1 (address B is
shown as 15 on the system).
If an ISDN module is attached,
keypad address C cannot be
connected to line 1 (address C is
shown as 16 on the system).
The Telecom, Printer Interface,
RS232, Ethernet and ISDN
modules can only be
connected to line 1.
If a Telecom module is attached,
keypad address E cannot be
connected to line 1(address E is
shown as 18 on the system).
If an RS232 module is attached,
keypad address D cannot be
connected to line 1 (address D is
shown as 17 on the system).
If an Ethernet module is attached,
keypad address B cannot be
connected to line 1 (address B is
shown as 15 on the system).
If an ISDN module is attached,
keypad address C cannot be
connected to line 1 (address C is
shown as 16 on the system).