Garmin GNX 120 7_inch Instruccion De Instalación
Connection Considerations
The marine instrument connects to power and to data sources
through a NMEA 2000 network. In addition, the marine
instrument can connect to a NMEA 0183 data source using a
data cable (not included).
NMEA 2000 Connection Considerations
NOTICE
If you have an existing NMEA 2000 network on your boat, it
should already be connected to power. Do not connect the
included NMEA 2000 power cable to an existing NMEA 2000
network, because only one power source should be connected
to a NMEA 2000 network.
If you are installing the included NMEA 2000 power cable, you
If you are installing the included NMEA 2000 power cable, you
must connect it to the boat ignition switch or through another in-
line switch. NMEA 2000 devices will drain your battery if the
NMEA 2000 power cable is connected to the battery directly.
The marine instrument connects to a NMEA 2000 network on
your boat using the port labeled NMEA 2000. The NMEA 2000
network provides power to the marine instrument and data from
NMEA 2000-compatible devices such as a wind sensor. The
included NMEA 2000 cables and connectors allow you to either
connect the device to your existing NMEA 2000 network or
create a basic NMEA 2000 network if needed.
If you are unfamiliar with NMEA 2000, you should read the
If you are unfamiliar with NMEA 2000, you should read the
“NMEA 2000 Network Fundamentals” chapter of the Technical
Reference for NMEA 2000 Products. To download the
reference, click the “Manuals” link on the product page for your
device at
Item
Description
À
Wind sensor
Á
Marine instrument
Â
Ignition or in-line switch
Ã
NMEA 2000 power cable
Ä
NMEA 2000 drop cable
Å
12 Vdc power source
Æ
NMEA 2000 terminator or backbone cable
Ç
NMEA 2000 T-connector
È
NMEA 2000 terminator or backbone cable
NMEA 0183 Connection Considerations
• The marine instrument can receive NMEA 0183 data from
one device using a NMEA data cable (not included), but it
cannot transmit data from the NMEA 0183 device to the
NMEA 2000 network.
• If are replacing a legacy Garmin marine instrument that
currently uses a NMEA data cable, you do not need to
purchase a new data cable, but you might need to replace
the quarter-turn locking ring with a threaded locking ring. See
your local Garmin dealer or
for more
information.
• The installation instructions provided with your NMEA 0183
compatible device should contain the information you need
to identify the transmitting (Tx) A (+) and B (-) wires.
• When connecting NMEA 0183 devices with two transmitting
wires, it is not necessary for the NMEA 2000 bus and the
NMEA 0183 device to connect to a common ground.
• When connecting a NMEA 0183 device with only one
transmitting (Tx) wire, the NMEA 2000 bus and the NMEA
0183 device must connect to a common ground.
• For extended runs, you should use at least 0.33 mm
2
(22 AWG) wire.
• You must solder and seal all connections with heat-shrink
tubing.
Wire Color Wire Function
Red
A red wire is present only on some variations of the data
cable, and should not be connected.
cable, and should not be connected.
Black
Accessory (-). This wire is used only when connecting the
marine instrument to a Garmin HVS GPS antenna.
marine instrument to a Garmin HVS GPS antenna.
Yellow
Accessory (+). This wire is used only when connecting the
marine instrument to a Garmin HVS GPS antenna.
marine instrument to a Garmin HVS GPS antenna.
Blue
Tx/A (+). This wire is used only when connecting the
marine instrument to a Garmin HVS GPS antenna.
marine instrument to a Garmin HVS GPS antenna.
White
Tx/B (-). This wire is used only when connecting the
marine instrument to a Garmin HVS GPS antenna.
marine instrument to a Garmin HVS GPS antenna.
2