Crown Audio IQ-USM 810 Manual De Usuario
©2000 Crown International, Inc.
Maintenance 4-7
130447-1 Rev. A
IQ-USM 810 Service Manual
4.6.20 CHASSIS GROUND
Spec:
Ground conductor of the power inlet is connected
to chassis ground.
Note: This test to be completed after the complete product
assembly.
assembly.
Procedure:
Verify power inlet less than 1 W between connector
ground and chassis.
Recommended chassis test points:
RS232 Connector shell or screw locks, Multi-Function
Control Port shell of screw locks or Crown bus connec-
tor shield.
Verify power inlet less than 1 W between connector
ground and chassis.
Recommended chassis test points:
RS232 Connector shell or screw locks, Multi-Function
Control Port shell of screw locks or Crown bus connec-
tor shield.
4.4.21 HI-POT
Spec:
Power Supply withstands Hi-Pot spikes.
Procedure:
Verify unit allows no breakdown leakage
current with a 1-second, 1.2-kV Hi-Pot from AC mains
(Hot and Neutral) to earth ground.
(Hot and Neutral) to earth ground.
4.7 Typical Measurements
Output Noise
20 Hz to 20 KHz bandwidth, line mode:
–77 dBu
Frequency Response
Frequency Response
20 Hz to 20 KHz, referenced to
1 KHz, line mode: –0.27 dB.
Harmonic Distortion
Harmonic Distortion
THD+N, at 1 KHz, 20 Hz to 20
KHz bandwidth, line mode, 0 dBu input: 0.013 %.
Common Mode Rejection
Common Mode Rejection
at 60 Hz, line mode: –66.5
dB.
Head Room / Input Clip Level
Head Room / Input Clip Level
highest input level be-
fore 1 % TDH+N, Line mode: –.131 % TDH+N @ +20
dBu.
Input Potentiometer
dBu.
Input Potentiometer
at 1 KHz, 0 dBu input:
Potentiometer
at –12 setting: –12.85 dB
at +20 setting: +20.43 dB
Phantom Supply
at –12 setting: –12.85 dB
at +20 setting: +20.43 dB
Phantom Supply
between each signal pin (“+ and “–”)
and ground of each input: 25.77 VDC
Control Port Output Voltage Pins
5 volt supply (between pins 9 and 10): 4.92 VDC
10 volt supply (between pins 29 and 28): 10.26 VDC
Control Port Output Voltage Pins
5 volt supply (between pins 9 and 10): 4.92 VDC
10 volt supply (between pins 29 and 28): 10.26 VDC
Object Number
Dec
Dec
Hex/ASN1 Description / Command string format
Bus Master: Allows manual control of the bus master function. (Normally an internal func-
tion of the Ucode protocol). With this object set, no IQ bus, communication passes through
the IQ-USM 810 Crown bus port.
tion of the Ucode protocol). With this object set, no IQ bus, communication passes through
the IQ-USM 810 Crown bus port.
Send: DA DT CT C0 05 09 01 CS; to master the IQ Bus, open the loop
Response: None
Send: DA DT CT C0 05 00 CS; to unmaster the IQ Bus, close the loop
Response: DA DT AK CT 00 CS; standard ACK
Response: None
Send: DA DT CT C0 05 00 CS; to unmaster the IQ Bus, close the loop
Response: DA DT AK CT 00 CS; standard ACK
704
$2C0
$C0 $05
$C0 $05
768
$300
$80 $06
$80 $06
Display Test Mode: Cycles each section of the display through a known sequence allowing
the operator to verify that all segments and indicators are functional. See Section 4.7 for
known sequence.
the operator to verify that all segments and indicators are functional. See Section 4.7 for
known sequence.
Send: DA DT CT 80 06 09 01 CS; To force the preset LED on
Response: DA DT AK CT 00 CS; standard ACK
Send: DA DT CT 80 06 09 00 CS; To set the preset LED in normal mode
Response: DA DT AK CT 00 CS; standard ACK
Response: DA DT AK CT 00 CS; standard ACK
Send: DA DT CT 80 06 09 00 CS; To set the preset LED in normal mode
Response: DA DT AK CT 00 CS; standard ACK
705
$2C1
$C1 $05
$C1 $05
Pushbutton Test: Reads a single byte that is bit mapped to indicate a pushbutton depres-
sion (bit 0 = “SEL” depressed, bit 1 =”
sion (bit 0 = “SEL” depressed, bit 1 =”
∧
” depressed, bit 2 = “
∨
” depressed):
Send: DA DT CT C1 05 0A CS, To get data
Response: DA DT AK CT C1 05 0C BTN CS
Response: DA DT AK CT C1 05 0C BTN CS
4.8 Test/Debug Objects