Futaba 10CAG Manual De Instrucciónes
46
Auxiliary channel function (including channel 9-10 controls)(AUX-CH
GH¿QHVWKHUHODWLRQVKLSEHWZHHQWKHWUDQVPLWWHU
controls and the receiver output for channels 5-10. Also, the CH9-10 POSI are used to change the CH9-10 servo direction.
Note that the CH9-10 functions are only visible in the AUX-CH screen when 2.4H-10CH modulation is selected. Channels
8-10 are not supported in 2.4G-7CH modulation.
Note that the CH9-10 functions are only visible in the AUX-CH screen when 2.4H-10CH modulation is selected. Channels
8-10 are not supported in 2.4G-7CH modulation.
Adjustability:
• Channels 5-8 may be assigned to any SWITCH (A-H), LOGIC SWITCH
• Channels 5-8 may be assigned to any SWITCH (A-H), LOGIC SWITCH
(Lsw1-Lsw3), slider [VR(D) and VR(E)], or knob [VR(A-C)] for example,
moving flaps to a switch or slider, but not the primary control sticks (use
programmable mixes to do so, p. 68). (GLID 1A+1F only): Channel 6 may be
assigned to Airbrake control stick (STK-ARBK).
moving flaps to a switch or slider, but not the primary control sticks (use
programmable mixes to do so, p. 68). (GLID 1A+1F only): Channel 6 may be
assigned to Airbrake control stick (STK-ARBK).
• Channels 9-10 may be assigned to any SWITCH (A-H), LOGIC SWITCH
(Lsw1-Lsw3) and the servo direction may be changed.
• Multiple channels may be assigned to the same switch, slider or knob;
• Channels set to "NULL" are only controlled by mixes. (Ex: utilizing 2
• Channels set to "NULL" are only controlled by mixes. (Ex: utilizing 2
channels for 2 rudder servos. See mixes, p. 68.)
• If GYRO SENSE, GOVERNOR, and THR-NEEDLE functions are activated, AUX-CH
settings of related channels become invalid automatically.
Related channels:
GYRO SENSE
GYRO SENSE
(ACRO): ch. 5, 7, or 8: see p. 73.
GYRO SENSE
(HELI): ch. 5: see p. 107.
GOVERNOR
(HELI): ch. 7, or ch. 7 and 8: see p. 108.
THR-NEEDLE
(ACRO
HELI): ch. 8: see p. 65.
Remember that if you assign primary control of a channel to a switch which you later use for other functions (like
GXDOWULSOHUDWHVRUDLUEUDNHV HYHU\WLPH\RXXVHWKDWRWKHUIXQFWLRQ\RXZLOODOVREHPRYLQJWKHDX[LOLDU\FKDQQHO
GXDOWULSOHUDWHVRUDLUEUDNHV HYHU\WLPH\RXXVHWKDWRWKHUIXQFWLRQ\RXZLOODOVREHPRYLQJWKHDX[LOLDU\FKDQQHO
GOAL of EXAMPLE:
STEPS:
INPUTS:
$VVLJQÀDSVWRWKHULJKWVOLGHU>VR(E)]
and set channel 7 to NULL in preparation
to use it as a smoke system control (the
smoke system being activated later by a
throttle-to-ch.-7 mix).
and set channel 7 to NULL in preparation
to use it as a smoke system control (the
smoke system being activated later by a
throttle-to-ch.-7 mix).
Open BASIC menu, then open AUX-CH
function.
function.
for 1 second.
(If ADVANCE,
again.)
to page 2.
C
to AUX-CH.
Choose the channel to change. (ex: ch.
6.)
6.)
C
to Ch 7.
Change primary control. (ex: to slider.)
to Vr-E.
Repeat as needed. (ex: ch. 7 to NULL.)
C
to Ch 7.
to NULL.
Close.
Where next?
Programmable mixes: see p. 68.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.
Adjust SUB-TRIM of auxiliary channel to adjust center SWITCH position:
see p. 49.
Adjust END POINTs (sets end points of travel even when using a switch):
see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.
Adjust SUB-TRIM of auxiliary channel to adjust center SWITCH position:
see p. 49.
Adjust END POINTs (sets end points of travel even when using a switch):
see p. 39.