Futaba 10CAG Manual De Instrucciónes
57
Dual Elevator Servos (with a rudder) (AILEVATOR) (ACRO): Many models use two elevator servos, plugged in separate
receiver channels. (Flying wings without a separate aileron control use ELEVON. V-shaped tail models use V-TAIL, p. 58.)
receiver channels. (Flying wings without a separate aileron control use ELEVON. V-shaped tail models use V-TAIL, p. 58.)
%HQH¿WV
• Ability to adjust each servo's center and end points for perfectly matched
• Ability to adjust each servo's center and end points for perfectly matched
travel.
• Ease of assembly, not requiring torque rods for a single servo to drive 2
surfaces.
(OHYDWRUVDFWLQJDOVRDVDLOHURQVIRUH[WUHPHVWXQWÀ\LQJRUPRUHUHDOLVWLFMHW
À\LQJ RSWLRQDO
• Redundancy, in case of a servo failure or mid-air collision.
Adjustability:
• CH2 and CH8 only. (With programmable mixing, could utilize CH5 as the 2nd elevator servo. See www.futaba-rc.com\
• CH2 and CH8 only. (With programmable mixing, could utilize CH5 as the 2nd elevator servo. See www.futaba-rc.com\
faq\ for examples.) THROTTLE-NEEDLE uses CH8 and cannot be active simultaneously.
• Direction of each servo's travel may be reversed in REVERSE or the set percentages may be reversed here.
• Elevator travels independently adjustable (both directions and percent).
• Optional action as ailerons (defaults to 50%
• Elevator travels independently adjustable (both directions and percent).
• Optional action as ailerons (defaults to 50%
UHVSRQVH 7KLV UHVSRQVH FDQQRW EH DFWLYDWHGGHDFWLYDWHG LQ ÀLJKW 6HWWLQJ
AIL1
and 2 to 0 disables this feature. Note: if you want this, but controlled with a switch, set AIL1 and 2 to 0 here, and use
2 mixes . AIL-to-ELEV and AIL-to-AUX2
OLQNWULPRIIDVVLJQDVZLWFK WRJHWDLOHURQDFWLRQIURPWKHHOHYDWRUVHUYRVZKHQ
the assigned switch is on. See p. 68.
)RUGHWDLOVRQVHWWLQJXSDFRPSOH[DHUREDWLFSODQHVXFKDVRQHZLWKZLQJVHUYRVIXOOVSDQDLOHURQVÀDSVAIRBRAKE/
crow etc, please visit www.futaba-rc.com\faq\. Many other setups are also available.)
crow etc, please visit www.futaba-rc.com\faq\. Many other setups are also available.)
The AILEVATOR mixing function uses one servo on each of the two elevators, and combines the elevator function with the
aileron function (unless aileron travel is set to 0). For aileron effect, the elevators are raised and lowered opposite of one
another in conjunction with the ailerons.
aileron function (unless aileron travel is set to 0). For aileron effect, the elevators are raised and lowered opposite of one
another in conjunction with the ailerons.
Once AILEVATOR is activated, unless you zero out the aileron values (see below), any time you move your ailerons or any
programming moves your ailerons (ie. RUDDER-AILERON mixing), the radio automatically commands both elevator servos
to also operate as ailerons. To deactivate this action, simply set the 2 aileron travel settings to 0 in the AILEVATOR function.
This way the elevators will work only as elevators.
programming moves your ailerons (ie. RUDDER-AILERON mixing), the radio automatically commands both elevator servos
to also operate as ailerons. To deactivate this action, simply set the 2 aileron travel settings to 0 in the AILEVATOR function.
This way the elevators will work only as elevators.
,IXVLQJWKHHOHYDWRUVDVDLOHURQVDVZHOOEHVXUHWRPRYHWKHHOHYDWRUDLOHURQVWLFNZKLOHFKHFNLQJWKHVHUYRPRWLRQV,ID
ODUJHWUDYHOLVVSHFL¿HGZKHQWKHVWLFNVDUHPRYHGDWWKHVDPHWLPHFRQWUROVPD\ELQGRUUXQRXWRIWUDYHO
ODUJHWUDYHOLVVSHFL¿HGZKHQWKHVWLFNVDUHPRYHGDWWKHVDPHWLPHFRQWUROVPD\ELQGRUUXQRXWRIWUDYHO
GOAL of EXAMPLE:
STEPS:
INPUTS:
Activate twin elevator servos.
Deactivate the elevator-acting-as-
ailerons portion of this function.
Deactivate the elevator-acting-as-
ailerons portion of this function.
Note: Depending upon your model's
geometry, you may need to reverse one
servo or set a negative percentage here.
geometry, you may need to reverse one
servo or set a negative percentage here.
Open the AILEVATOR function.
for 1 second.
(If BASIC,
again.)
C
to AILEVATOR.
Activate the function.
C
to MIX.
to ACT.
Optional: adjust up/down travel when
operating as ailerons. (Ex: 0.)
operating as ailerons. (Ex: 0.)
C
to AIL3.
to 0%.
C
to AIL4.
to 0%.
Optional: adjust total elevator travel
of each servo. (Ex: right servo elevator
travel to 98%, left to 96%.)
of each servo. (Ex: right servo elevator
travel to 98%, left to 96%.)
C
to ELE2.
to 98%.
C
to ELE1.
to 96%.
Close menu.
Where next?
Adjust individual servo's SUB-TRIMs: see p. 49 and END POINTs: see p. 39.
Set up Twin Aileron Servos: see p. 51.
Set up AIRBRAKE mix: see p. 63.
Set up Twin Aileron Servos: see p. 51.
Set up AIRBRAKE mix: see p. 63.