Futaba 10CAG Manual De Instrucciónes
78
$/22.$77+(5$',2
6GLID-SPECIFIC FUNCTIONS STEP BY STEP.
Those functions which are identical to the ACRO setups are referred directly to those pages.
Those functions which are identical to the ACRO setups are referred directly to those pages.
MODEL TYPE
: This function of the PARAMETER submenu is used to select the type of model programming to be used.
GLIDER TYPES:
%HIRUHGRLQJDQ\WKLQJHOVHWRVHWXSDJOLGHURUVDLOSODQH¿UVW\RXPXVWGHFLGHZKLFKMODEL TYPEEHVW¿WV\RXUDLUFUDIW
• ACRO
• ACRO
IRUVRPHDHUREDWLFVORSHJOLGHUVACRO is a better choice because of functions it offers that the GLID types do not.
• ACRO provides:
• SNAP-ROLL,
• AILEVATOR (twin elevator servo support),
• AIRBRAKE (a more assignable version of BUTTERFLY).
• For nitro-powered sailplanes: IDLE-DOWN, THR-CUT, THROTTLE-NEEDLE mixing and THROTTLE DELAY programming.
• AILEVATOR (twin elevator servo support),
• AIRBRAKE (a more assignable version of BUTTERFLY).
• For nitro-powered sailplanes: IDLE-DOWN, THR-CUT, THROTTLE-NEEDLE mixing and THROTTLE DELAY programming.
• But ACRO
ODFNV SURJUDPPLQJ IRU IXOOVSDQ DLOHURQV DQG VHSDUDWH 2))6(7 WULPV IRU HDFK ÀLJKW FRQGLWLRQ 1RUPDO
Start, Speed, Distance and Landing.
• GLID(1A+1F): The GLID(1A+1F) MODEL TYPE is intended for sailplanes with one or two aileron servos (or none), and a single
ÀDS VHUYR RU WZR FRQQHFWHG ZLWK D \FRQQHFWRU 7KLV TYPE is meant to be a very simplistic version to set up a basic
JOLGHUZLWKRXWDORWRIDGGHGIHDWXUHV$GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH
JOLGHUZLWKRXWDORWRIDGGHGIHDWXUHV$GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH
• GLID(2A+1F): The GLID(2A+1F) MODEL TYPE
LVLQWHQGHGIRUVDLOSODQHVZLWKGXDODLOHURQVHUYRVDQGDVLQJOHÀDSVHUYR RU
WZRFRQQHFWHGZLWKD\FRQQHFWRU $GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH7KHVHÀLJKWFRQGLWLRQVFRQWDLQGLIIHUHQWRIIVHW
trims and aileron differentials to make the sailplane perform certain maneuvers more easily.
trims and aileron differentials to make the sailplane perform certain maneuvers more easily.
• GLID(2A+2F): The GLID(2A+2F) MODEL TYPE supports dual flap servos that can also act as ailerons, creating full-span
DLOHURQVDQGÀDSV$GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH7KHVHÀLJKWFRQGLWLRQVFRQWDLQGLIIHUHQWRIIVHWWULPVDQGDLOHURQ
differentials to make the sailplane perform certain maneuvers more easily.
differentials to make the sailplane perform certain maneuvers more easily.
GOAL of EXAMPLE:
STEPS:
INPUTS:
C h a n g e m o d e l 1 i s MODEL T YPE t o
GLID(1A+1F)
GLID(1A+1F)
.
N O T E : T h i s i s o n e o f t h e s e v e r a l
f u n c t i o n s t h a t t h e r a d i o re q u i re s
FRQ¿UPDWLRQWRPDNHDFKDQJH
f u n c t i o n s t h a t t h e r a d i o re q u i re s
FRQ¿UPDWLRQWRPDNHDFKDQJH
Confirm you are currently using the
proper model memory. (Ex: 1)
proper model memory. (Ex: 1)
On home screen, check model nameand
number on top left.
number on top left.
If it is not the correct model (Ex: 1), use
MODEL SELECT
MODEL SELECT
, p. 25.
Open PARAMETER submenu.
for 1 second.
(If ADVANCE,
again.)
to 2nd page of menu.
C
to PARAMETER.
Change the MODEL TYPE.
&RQ¿UPWKHFKDQJH
&RQ¿UPWKHFKDQJH
C
to TYPE.
to GLID(1A+1F).
for one second.
Are you sure?
&RQ¿UPDWLRQGLVSOD\V
WRFRQ¿UP
Close.
GLID(1A+1F)
(FLAPERON)
(FLAPERON)
AIL1
FLP2
(CH1)
AIL2
FLP1
(CH6)
AIL1
(CH1)
AIL2
(CH7)
FLP
(CH6)
GLID(2A+1F)
AIL1
(CH1)
FLP1
(CH6)
FLP2
(CH5)
AIL2
(CH7)
GLID(2A+2F)