KRAM Audio2Car 84941 Prospecto
Los códigos de productos
84941
Audio2Car
The professional mute
The professional mute
Audio2Car
Installation description
for car specific Audio2Car harness
Needed items:
A: Audio2Car harness.
B: Audio2Car carkit adaptor (or Mute-box from our Drive & Talk
range see last page).
C: Carkit.
Note: The Carkit C and Audio2Car carkit adaptor B bought sepa-
rately.
Installation:
1st: Remove the key from the ignition barrel. This is done to
avoid error messages on the cars electrical system.
Note: On some
cars it may even be necessary to remove the ground pole from the
car battery.
2nd: Locate & uncover the radio / amplifier unit. The radio /
amplifier unit is normally found in the front of the car where the
CD-player or radio tuner is located.
Cars with special radio / amplifier locations:
car battery.
2nd: Locate & uncover the radio / amplifier unit. The radio /
amplifier unit is normally found in the front of the car where the
CD-player or radio tuner is located.
Cars with special radio / amplifier locations:
•
BMWs with navigation system often has the radio unit behind side panel in boot. For these cars an
Audio2Car extension cable item no. AE5 is also required.
Audio2Car extension cable item no. AE5 is also required.
•
BMW X5 has the radio unit located in the spare wheel well. An Audio2Car extension cable item no.
AE5 is also required.
AE5 is also required.
•
Mercedes A, B, C & CLK class with sound system upgrade (code 810) install on amplifier behind
right side panel in boot just behind the rear wheel arch. An Audio2Car extension cable item no. AE5 is
also required.
right side panel in boot just behind the rear wheel arch. An Audio2Car extension cable item no. AE5 is
also required.
•
Mercedes CL & S class with BOSE sound system (code 810) install on amplifier placed in the left
side of the boot below the navigation unit and CD changer unit. It may be necessary to completely
remove the left boot interior panel. An Audio2Car extension cable item no. AE5 is also required.
side of the boot below the navigation unit and CD changer unit. It may be necessary to completely
remove the left boot interior panel. An Audio2Car extension cable item no. AE5 is also required.
•
Mercedes ML & GL class with Harman Kardon sound system (code 810) Install on amplifier placed
under the drivers seat. Under the carpet there is small room where the amplifier is located. It may be
necessary to completely remove the drivers seat. An Audio2Car extension cable item no. AE4 is also
required.
under the drivers seat. Under the carpet there is small room where the amplifier is located. It may be
necessary to completely remove the drivers seat. An Audio2Car extension cable item no. AE4 is also
required.
•
Renault cars install on CD-player in front, on amplifier located inside dash behind/above glove box,
below front seat or in the boot. An Audio2Car extension cable may be required. Please check the
complete cable list for a description of the radio / amplifier unit location for the specific car model.
below front seat or in the boot. An Audio2Car extension cable may be required. Please check the
complete cable list for a description of the radio / amplifier unit location for the specific car model.
•
Volvo C30 with High Performance sound system install on amplifier behind rear side speaker. right
side in left hand drive cars and left side in right hand drive cars. An Audio2Car extension cable item
no. AE5 is also required.
side in left hand drive cars and left side in right hand drive cars. An Audio2Car extension cable item
no. AE5 is also required.
•
Volvo S40 & V50 2004- with High Performance sound system install on amplifier unit behind side
panel in boot. An Audio2Car extension cable item no. AE5 is also required.
panel in boot. An Audio2Car extension cable item no. AE5 is also required.
•
Volvo XC60, V70, XC70, S80, XC90 from 2006- with High Performance sound system install on
amplifier below front passenger seat. An Audio2Car extension cable item no. AE4 is also required.
amplifier below front passenger seat. An Audio2Car extension cable item no. AE4 is also required.
3rd: Connect the car-specific cable. Disconnect the connector on the radio / amplifier unit and insert the
Audio2Car harness between the connector and radio / amplifier unit.
Note: Some radios may require a security
code to be entered after the power / connectors have been removed.
4th: Connect the blue ignition wire. If an ignition source exists in the connector on the Audio2Car harness the
blue ignition wire is connected to this position. If no ignition source is available in the connector then the blue
4th: Connect the blue ignition wire. If an ignition source exists in the connector on the Audio2Car harness the
blue ignition wire is connected to this position. If no ignition source is available in the connector then the blue
See our complete Radio Mute program on our website
www.kram.dk
ignition wire is connected to the constant 12v source with a bullet connector. If an ignition source is needed for
the chosen carkit IGNIBOX item no. “I” can be inserted to create an artificial ignition source or the blue ignition
wire can be disconnected from the red constant 12v and manually connected to an ignition source found else-
where.
5th: Connect the mute wire. If a Mute input exists in the connector on the Audio2Car harness the yellow mute
wire is connected to this position when delivered. If no Mute input is available in the connector then the yellow
mute wire is found close to the male connector fitted with a bullet connector. It can then be manually con-
nected to a mute input. Connecting the mute wire is an option but may be required in some cars to achieve a
full mute of all speakers.
the chosen carkit IGNIBOX item no. “I” can be inserted to create an artificial ignition source or the blue ignition
wire can be disconnected from the red constant 12v and manually connected to an ignition source found else-
where.
5th: Connect the mute wire. If a Mute input exists in the connector on the Audio2Car harness the yellow mute
wire is connected to this position when delivered. If no Mute input is available in the connector then the yellow
mute wire is found close to the male connector fitted with a bullet connector. It can then be manually con-
nected to a mute input. Connecting the mute wire is an option but may be required in some cars to achieve a
full mute of all speakers.
Note: Not all cars are equipped with a mute input.
6th: Check fuse size. The fuse on the Audio2Car cable should not be bigger than the ones used on the wiring
loom supplied with the carkit. The fuses on the Audio2Car cable should be replaced with a size similar to the
ones supplied with the carkit.
Note: Never exceed the Maximum Fuse size for the Audio2Car cable. See first page.
7th: Connect the carkit adaptor (or Drive & Talk Mute-box). Connect the carkit adaptor to the 24 pin connec-
tor on the Audio2Car harness. Connect the carkit adaptor to the carkit.
Troubleshooting Guide
Carkit does not start up. Check if there is 12V between the black and the red wire and also between the black
and blue wire, in the 24 pin connector, when the car is started. If there is not 12v on both wires please check
the following:
1.
and blue wire, in the 24 pin connector, when the car is started. If there is not 12v on both wires please check
the following:
1.
If there is supply on the red constant 12v wire but not on the blue ignition wire the car may require an
alternative ignition source. See installation step 4.
alternative ignition source. See installation step 4.
2.
Check that the bullets on the supply wires are properly connected. The supply wires are the red, blue
and black wires.
and black wires.
3.
Check for a blown fuse on the Audio2Car harness or in the cars fuse-box.
The carkit does not turn off when the key is removed from the ignition barrel. Your carkits needs a real igni-
tion source. Please check the following:
1.
tion source. Please check the following:
1.
Is the blue ignition wire connected to the red constant 12v wire with a bullet connector? If this is the
case then there is no ignition supply in the radio connector. See installation step 4.
case then there is no ignition supply in the radio connector. See installation step 4.
2.
Is there an ignition supply on the blue wire. There should be no voltage on the blue wire when there is
no key in the ignition. See installation step 4.
no key in the ignition. See installation step 4.
Not all speakers are muted. Try to disconnect the Carkit adaptor (or mute-box) from the Audio2Car harness
then turn on the radio and check the following :
1.
then turn on the radio and check the following :
1.
All speakers keep playing: This is the wrong Audio2Car harness for this car / sound system.
2.
Only a few speakers keep playing: The mute wire needs to be connected, see installation step 5 or this
is the wrong Audio2Car harness for this car / sound system.
is the wrong Audio2Car harness for this car / sound system.
3.
All speakers are now muted:
•
Carkits with 1 speaker mute: Some carkits can only mute 1 speaker channel with their build
in mute-box. This is normally stated on the label on the carkit adaptor for these carkits, else
please check the carkit manual. If a full mute is desired with these carkits, then this can be
achieved by either connecting the mute wire, see installation step 5. Or adding a mute-box
from our Drive & Talk range.
in mute-box. This is normally stated on the label on the carkit adaptor for these carkits, else
please check the carkit manual. If a full mute is desired with these carkits, then this can be
achieved by either connecting the mute wire, see installation step 5. Or adding a mute-box
from our Drive & Talk range.
•
Carkits with 4 speaker mute: (or when Kram mute-box is used): The carkit is defective,
please replace the carkit.
please replace the carkit.
Radio will not turn on or not working properly after installation.
1.
1.
Please check for a blown fuse at the radio or in the car fuse-box.
2.
Remove the Audio2Car harness and connect the radio to the original car connector. If the radio is now
working replace the Audio2car harness.
working replace the Audio2car harness.
A: Audio2Car Harness
Item number 84xxx
Item number 84xxx
B: Audio2Car Adaptor
Item number AAxxx
Item number AAxxx
C: Carkit
24 pin Connectors
Bullet Connectors