American Dryer Corp. Milnor Phase 7.2.2 Manual De Usuario
5
N. Temperature Conversion Status – Temperature-related programs can be set in either Fahrenheit (°F) or
Celsius (°C). ALL temperatures will automatically convert to the corresponding values (+/- 1°) when
changes are made.
changes are made.
O. High Temperature Protection – If the Phase 7 non-coin microprocessor controller (computer) senses
that the temperature in the basket (tumbler) has exceeded 180° F (82° C) for axial airflow, or 220° F (104°
C) for radial airflow, it will end the drying cycle and a fault code will be displayed, indicating an overheating
problem.
C) for radial airflow, it will end the drying cycle and a fault code will be displayed, indicating an overheating
problem.
P. Cycle Preview – Entire dryer parameters (programs), or the preprogrammed cycles, are displayed for
verification upon a coded entry to the keyboard (touch pad).
Q. Reversing Option – Helps reduce the balling up or tangling of large items. A cycle can be set to have the
reversing option, so that the basket (tumbler) will turn in the forward direction for 30- to 120-seconds, stop
for 5- to 10-seconds, and then proceed in the reverse direction for the same time. This process is repeated
throughout the drying and cooling cycles.
for 5- to 10-seconds, and then proceed in the reverse direction for the same time. This process is repeated
throughout the drying and cooling cycles.
R. Rotation Sensor – The Phase 7 non-coin microprocessor controller (computer) also displays basket (tumbler)
rotations per minute (RPM) by pressing and holding the “DOWN ARROW” key while the basket (tumbler)
is on. (The basket [tumbler] must be rotating for approximately 30-seconds before getting a true RPM
reading).
is on. (The basket [tumbler] must be rotating for approximately 30-seconds before getting a true RPM
reading).
S. Clean Lint – This feature monitors the value of the “Lint Cleaning Frequency” timer. The timer keeps track
of how long the dryer’s blower/fan has been on, and compares it to the Lint Cleaning Frequency Setting.
Once the timer equals the Lint Cleaning Frequency setting, the Phase 7 non-coin microprocessor controller
(computer) will begin to prompt the user to “CLEAN LINT”. The Phase 7 non-coin microprocessor controller
(computer) will allow two (2) additional hours of run time before the Phase 7 non-coin microprocessor
controller (computer) is locked out in a “CLEAN LINT” state. The dryer will not be cleared from this state
until the lint drawer has been cleaned. When the lint drawer is opened, the display will read “Lint Access
Open”, and when the lint drawer is closed, the display will read “READY”.
Once the timer equals the Lint Cleaning Frequency setting, the Phase 7 non-coin microprocessor controller
(computer) will begin to prompt the user to “CLEAN LINT”. The Phase 7 non-coin microprocessor controller
(computer) will allow two (2) additional hours of run time before the Phase 7 non-coin microprocessor
controller (computer) is locked out in a “CLEAN LINT” state. The dryer will not be cleared from this state
until the lint drawer has been cleaned. When the lint drawer is opened, the display will read “Lint Access
Open”, and when the lint drawer is closed, the display will read “READY”.
T. Language Selection – Phase 7 non-coin microprocessor controller (computer) has the ability to display five
(5) different languages: English, French, Spanish, Italian, and German.
U. Model Selection – Phase 7 non-coin microprocessor controller (computer) can be programmed to be used
on three (3) modes of heat: gas, steam, and electric. It can also be configured for reversing and
non-reversing dryers.
non-reversing dryers.
V. Default Factory Settings – This feature will set ALL programmed parameters to their default values.
W. Keyboard (Touch Pad) Symbols –
= “STOP/CLEAR” key
= “START/ENTER” key
= “UP ARROW” key (scroll up)
= “DOWN ARROW” key (scroll down)
X. Steam Injection Option – The Phase 7 non-coin microprocessor controller (computer) has the ability to
program up to five (5) steam injection intervals, for a programmed amount of time, at different points of a
cycle including cool down.
cycle including cool down.