Brinsea OvaEasy 190 Advance EX Manual De Usuario
MJ192 GB Issue 02
3
2 Unpacking & Assembly
2.1
Your incubator has been supplied in protective packaging. Please remove all tape, strapping and packing from
the incubator parts. Retain the carton and packing materials to enable the unit to be repacked.
the incubator parts. Retain the carton and packing materials to enable the unit to be repacked.
2.2
Please check that parts are all present and undamaged.
2.3
Check also that the electrical supply matches the machine’s requirements (marked on the technical label on the
outside of the box and on the top cover of the Incubator).
outside of the box and on the top cover of the Incubator).
2.4
To register your new Brinsea product please visit www.brinsea.co.uk and follow the link on the right hand side
of the home page to qualify for your free 2 year guarantee.
of the home page to qualify for your free 2 year guarantee.
2.5
Go to www.Brinsea.co.uk and register as a free member of the Brinsea Email Group to receive the latest news
and information such as advance notice about new products, special offers, exclusive competitions and much
more.
and information such as advance notice about new products, special offers, exclusive competitions and much
more.
3 Location and Installation
THE INCUBATOR MUST BE PLACED IN AN INDOOR AREA NOT SUBJECT TO SPLASHES OF WATER
OR WET CONDITIONS AND OUT OF REACH OF ANIMALS AND CHILDREN.
3.1
Your incubator will give best results in a room free from wide temperature variations and with generous
ventilation – particularly if several incubators are running at the same time. Ensure that the room temperature
cannot drop on a cold night. Ideally thermostatically control the room at between 20 and 25°C (68 and 77°F).
Never allow the room temperature to drop below 15°C (59°F) and ensure that the incubator cannot be exposed to
direct sunlight.
ventilation – particularly if several incubators are running at the same time. Ensure that the room temperature
cannot drop on a cold night. Ideally thermostatically control the room at between 20 and 25°C (68 and 77°F).
Never allow the room temperature to drop below 15°C (59°F) and ensure that the incubator cannot be exposed to
direct sunlight.
3.2
Always place the incubator upright on a flat level surface. The 190 size incubator weighs 20Kg and the 380 size
incubator weighs 27Kg. Ensure the surface is adequate to support the weight of the machine and contents.
incubator weighs 27Kg. Ensure the surface is adequate to support the weight of the machine and contents.
3.3
Open the door, slide out the Evaporation Tray and fill with 1:200 mix of water and Brinsea disinfectant solution.
The water level should be no higher than approx 1” (2.5cm) from the top. The evaporating block is not normally
needed unless very high humidity levels (e.g. for hatching) are required or the optional Advance Humidity Pump
is being used. Close the door.
The water level should be no higher than approx 1” (2.5cm) from the top. The evaporating block is not normally
needed unless very high humidity levels (e.g. for hatching) are required or the optional Advance Humidity Pump
is being used. Close the door.
3.4
Plug the incubator supply cable into a suitable outlet ensuring that the cable is not pulled tight. The incubator
fans will start, the buzzer sound and the LCD display will show the air temperature and humidity.
fans will start, the buzzer sound and the LCD display will show the air temperature and humidity.
4 Quick Reference (please read relevant section for detail)
This quick reference is intended to allow users to quickly set up the incubator and learn the key features of the control
system. Please read the rest of the instructions to obtain a full understanding of each feature.
PRESS BOTH BUTTONS TO UNLOCK THE MAIN MENU
SELECT THE OPTION / RETURN TO THE MENU.
GO FORWARD ONE SCREEN / INCREASE THE VALUE / DISPLAY IN CELSIUS.
GO BACK ONE SCREEN / DECREASE THE VALUE / DISPLAY IN FAHRENHEIT.
PRESS BOTH BUTTONS TO TURN NOW (THEN ANY BUTTON TO PAUSE / STOP)