Bosch Appliances Home Security System D9412GV2 Manual De Usuario
D9412GV2/D7412GV2 | Operation and Installation Guide | 10.0
Off-Board Relays
.
Bosch Security Systems, Inc. | 5/05 | F01U003641B
49
Figure 21: D8129 Connections to the D7412GV2
Pin
Battery
amming
E CONNECTIONS
POWER +
DATA BUS A
DATA BUS B
COMMON
ZONEX OUT 1
ZONEX IN 1
32
31
30
29
28
27
NOT USED
26
25
NOT USED
EX POWER +
24
X COMMON
23
D5200/D5360
PROG CONN
PROG CONN
2
3
3
1
2
3
4
5
6
7 8
1
DATA
AUX
GND
1 - D8129 OctoRelays for relay numbers 1 to 64.
Connect OctoRelays in parallel.
2 - Power limited
3 - Supervised, power limited
10.1.1 Configuring the D8129 OctoRelay
Five switches on the OctoRelay determine the relay
numbers for the eight relay outputs (
numbers for the eight relay outputs (
Error! Reference
source not found.
).
Table 18:
D8129 OctoRelay Switch Settings
Panel Relay
Number
Number
D8129 OctoRelay
Switch Setting
Switch Setting
On Panel, Connect
D8129 to:
D8129 to:
1 to 8
Off-On-On-On-On
Zonex 1 Terminal 28
9 to 16
On-Off-On-On-On
Zonex 1 Terminal 28
17 to 24
Off-Off-On-On-On
Zonex 1 Terminal 28
25 to 32
On-On-Off-On-On
Zonex 1 Terminal 28
33 to 40
Off-On-Off-On-On
Zonex 1 Terminal 28
41 to 48
On-Off-Off-On-On
Zonex 1 Terminal 28
49 to 56
Off-Off-Off-On-On
Zonex 1 Terminal 28
57 to 64
On-On-On-Off-On
Zonex 1 Terminal 28
D7412G Maximum
65 to 72
Off-On-On-On-On
Zonex 2 Terminal 26
73 to 80
On-Off-On-On-On
Zonex 2 Terminal 26
81 to 88
Off-Off-On-On-On
Zonex 2 Terminal 26
89 to 96
On-On-Off-On-On
Zonex 2 Terminal 26
97 to 104
Off-On-Off-On-On
Zonex 2 Terminal 26
105 to 112
On-Off-Off-On-On
Zonex 2 Terminal 26
113 to 120
Off-Off-Off-On-On
Zonex 2 Terminal 26
121 to 128
On-On-On-Off-On
Zonex 2 Terminal 26
10.1.2 Relay
Outputs
Relay outputs can activate when you are
setting the OctoRelay switches or
programming the control panel.
setting the OctoRelay switches or
programming the control panel.
Disconnect equipment connected to relay
outputs when you perform these functions.
outputs when you perform these functions.
Each OctoRelay output provides a Form C dry contact
rated for 1.0 A at 12 VDC. Normally-open, common,
and normally-closed terminals are available for each
relay output. When an individual output is activated,
there is continuity between the normally-open and
common terminals. When the output is not activated,
there is continuity between the normally-closed and
common terminals.
rated for 1.0 A at 12 VDC. Normally-open, common,
and normally-closed terminals are available for each
relay output. When an individual output is activated,
there is continuity between the normally-open and
common terminals. When the output is not activated,
there is continuity between the normally-closed and
common terminals.
10.1.3 Installation
Set the switches on the OctoRelay before installing it in
the enclosure. Refer to Section 10.1.1 Configuring the
D8129 OctoRelay on this page.
the enclosure. Refer to Section 10.1.1 Configuring the
D8129 OctoRelay on this page.
Install the OctoRelay in the enclosure with the control
panel (Figure 2 on page 9) or in an adjacent enclosure
that is no more than 1.5 m (5 ft.) from the control
panel. Use 1.5 mm (16 AWG) to 0.8 mm (22 AWG)
wire.
panel (Figure 2 on page 9) or in an adjacent enclosure
that is no more than 1.5 m (5 ft.) from the control
panel. Use 1.5 mm (16 AWG) to 0.8 mm (22 AWG)
wire.