Bionaire BCH3220 Manual De Usuario
For BCH3210:
1. Set the THERMOSTAT knob to the highest setting,
clockwise as far as it will turn.
2. When the desired room temperature level is reached,
lower the thermostat setting, by turning the
THERMOSTAT knob counter clockwise as far as
it will turn.
THERMOSTAT knob counter clockwise as far as
it will turn.
3. The thermostat will now automatically maintain the
pre-set temperature level by turning the heater on and
off. The thermostat is now set.
off. The thermostat is now set.
For BCH3220:
1. To change the heater settings, press the MODE button.
Each time you press the MODE button, it will scroll
through the settings FAN, LOW, HIGH, AUTO.
through the settings FAN, LOW, HIGH, AUTO.
Note: The fan speed will not change when the
mode is changed from low to high.
mode is changed from low to high.
2. Select the AUTO mode.
3. Set the heater to the desired room temperature by
pressing the (+) or (-) buttons.
Note that the degree range is from 60°F - 85°F
(15°C - 29°C). If you scroll past 85°F (29°C) the
display will automatically loop to 60°F (15°C).
(15°C - 29°C). If you scroll past 85°F (29°C) the
display will automatically loop to 60°F (15°C).
4. Now the desired temperature is set.
Note: When the temperature in the proximity of the heater
reaches the set temperature, the heater will automatically
turn on. The fan will continue to run cooling the heater for
30 seconds. The unit will operate again when the
temperature falls below the preset temperature.
reaches the set temperature, the heater will automatically
turn on. The fan will continue to run cooling the heater for
30 seconds. The unit will operate again when the
temperature falls below the preset temperature.
☛
TIP: It is normal for the heater to cycle ON and OFF as
it maintains the preset temperature. To prevent the unit
from cycling, raise the thermostat setting.
it maintains the preset temperature. To prevent the unit
from cycling, raise the thermostat setting.
90
°
SWIVEL INSTRUCTIONS
For maximum heat distribution use the revolutionary vertical
twin housing configuration to allow heat to travel in two
different directions.
twin housing configuration to allow heat to travel in two
different directions.
1. Carefully adjust each swivel to direct the heat flow.
2. Do not swivel the unit beyond the point of resistance.
NIGHTLIGHT (BCH3220 only)
1. The nightlight will automatically light when the room
becomes dark. When the room becomes light, the
nightlight will automatically turn off.
nightlight will automatically turn off.
2. To turn the nightlight off, press the button on the
control panel.
☛
TIP: The nightlight will not automatically operate until
the button is pressed again.
the button is pressed again.
MAINTENANCE INSTRUCTIONS
During Season Care
1. Before cleaning make sure the unit is unplugged.
Allow the heater to cool before cleaning.
2. Carefully wipe the unit with a soft, damp cloth.
Please be cautious near the heating elements.
☛
TIP: Over time, dust may accumulate on the front
grills. This can be removed by wiping the unit with a
damp cloth. Always unplug unit and allow to cool
prior to cleaning.
grills. This can be removed by wiping the unit with a
damp cloth. Always unplug unit and allow to cool
prior to cleaning.
After Season Care
Store heater in a cool, dry location. Bionaire
®
recommends
storing the unit in its original, or appropriately sized, box.
4
5
Mode
HIGH
LOW
FAN
AUTO
ROOM
TEMP.
TEMP.
SET
TEMP.
BCH3220
Power
Button
Current Room
Temperature
Indicator
Night Light
Button
Light
Sensor
Mode
Button
Set
Temperature
Indicator
Set Temperature
Higher
Lower
mode
thermostat
ff
Fan
Low
High
BCH3210
Figure 1