Billy Goat FM3300IN Manual De Usuario

Part No. 520166                                             

 

 

 

 

 

 

 

Form No. F112003A

..

..

Page 4 of 20

Your Billy Goat Mower is shipped from the factory 
in one crate, completely assembled except for the 
handles and console assembly.

8. Insert one of the handle mounting bolts (Item 102) with Hex. lock washer 
(Item 6) through the rear handle mounting hole of the right side handle, 
and screw it into the rear handle mounting hole on the right side of engine 
base chassis (Item 61).  Repeat this 
procedure for the left side using the 
left handle.
9.On each side of the mower, insert 
one of the handle mounting bolts 
(Item 102) with Hex. lock washer 
(Item 6) through the hole in one 
end of the handle brace (Item 32), 
the front handle mounting hole of 
the handle and screw into the front 
handle mounting hole in the engine 
base chassis (Figure 11-5).
10.Using one of the bolts and fl at 
washers removed previously (step 
8),  insert the bolt with washer, from 
the outside, through the bottom hole 
on the console, through the handle, 
through the top hole of the handle 
brace, through one of the fl at wash-
ers removed in step 8 and secure 
with lock nut (Item 151).  Repeat this 
procedure for the bottom hole on 
the other side of the console. Make 
sure control cables are free and not 
damaged while tightening console 
mounting bolts (Figure 6).
11.On the left hand side, using 
one of the bolts and fl at washers 
removed previously (step 6), insert 
the bolt with washer, from the 
outside, through the top hole on 
the console, through the handle, 
through the control cable retainer, 
through one of the fl at washers 
removed in step 8 and secure with 
lock nut (Item 151).  Repeat for right-
hand side except there is no control 
cable retainer for this side. Make 
sure the control cables are not 
damaged while tightening console 
mounting bolts (see fi gure 11-6).  
12.Finish mounting handle to 
engine base bolts then fi nish tight-
ening the remaining bolts. 
13.Position control cables and use 
2 cable ties on each handle to 
secure the cables in position.  The 
top cable tie should be 1” below the 
console and the lower tie should be 
12” below the console (see fi gure 
11-7)
14.Check the position of the shift rod 
guide (Item 69), and if necessary, 
snap it in place in the shift bracket 
(Item 78) as shown in Figure 11-8.
15.Put shift lever in NEUTRAL, 
depress the brake lever (release 
the brake) and carefully pull the 
machine back off the pallet.
16.Fill with oil and gas to the proper 
level and the unit is ready to mow.  
(a battery will also have to be 
installed on electric models.)
17.Read the operator’s manual.

1.Cut and remove the nylon retaining straps (see fi gure 11-1).
2.Pry up and remove the shipping crate’s top panel.
3.Remove the shipping crate’s end panel at rear of mower 
4.With the console positioned as shown in Figure 11-3, insert the shift 
linkage rod (Item 31) into the shift linkage connector (Item 54).  
5. To assemble the shift rod (item 31) to the shift linkage (item 54), 
use the roll pin in the parts/literature bag. If you’ll notice on the shift 
linkage, the hole is larger on one side than the other. 
It will be easier to start the roll pin from the larger side, forcing it 
through the shift rod and the hole on the other side of the shift linkage, 
using a hammer or large adjustable pliers.  
6.Remove and retain for reuse console mounting bolts, washers and 
nuts (Items 135, 150 & 151) from left and right handles.
7.Remove and retain for reuse handle mounting bolts and hex lock 
washers (Items 102 & 6) located just above the rear wheels on each 
side of mower (see fi gure 11-4). 
NOTE: Fasteners should only 
be tightened snug tight until 
handle and console assembly 
is complete. 

NOTE: All item numbers called out in the assembly, 
operation, and maintenance sections of this manual can 
be found on Parts List (pages 15-18).

Figure 11-1

Figure 11-3

Figure 11-4

Figure 11-5

Figure 11-6

Figure 11-7

Figure 11-8