Behringer XENYX MIXER X1204USB Manual De Usuario

XENYX 1204USB/X1204USB User Manual

XENYX 1204USB/X1204USB User Manual

POWER 
Use the POWER switch to power up the mixing console.

PHANTOM
The PHANTOM switch activates the phantom power supply 

for the XLR connectors of the mono channels which is 

required to operate condenser microphones. The red  

+48 V LED lights up when phantom power is on. As a rule,  

dynamic microphones can still be used with phantom  

power switched on, provided that they are wired in a 

balanced configuration. In case of doubt, contact the 

microphone manufacturer!

SERIAL NUMBER
Please note the important information on the serial number 

given in chapter 1.3.3.

24-BIT MULTI-EFFECTS PROCESSOR
Here you can find a list of all presets stored in the multi-

effects processor. This built-in effects module produces 

high-grade standard effects such as reverb, chorus, flanger, 

delay and various combination effects. The integrated  

effects module has the advantage of requiring no wiring.  

This way, the danger of creating ground loops or uneven 

signal levels is eliminated at the outset, completely 

simplifying the handling.
These effect presets are designed to be added to dry signals. 

If you move the FX TO MAIN control, you mix the channel 

signal (dry) and the effect signal.
This also goes for mixing effects signals with the monitor 

mix. The main difference is that the mix ratio is adjusted 

using the FX TO MON control. Of course, a signal has to 

be fed into the effects processor via the FX control in the 

channel strip for both applications.

LEVEL
The LED level meter on the effects module should display 

a sufficiently high level. Take care to ensure that the clip 

LED only lights up at peak levels. If it is lit constantly, you 

are overloading the effects processor and this could 

cause unpleasant distortion. The FX control (AUX SEND 2) 

determines the level that reaches the effects module.

PROGRAM
You can select the effect preset by turning the PROGRAM 

control. The display flashes the number of the current  

preset. To recall the selected preset, press the button; the 

flashing stops. You can also recall the selected preset with 

the foot switch.

The packaging of your mixing console contains two 19" rack 

mount wings which can be installed on the side panels of 

the console.
Before you can attach the rack mount wings to the mixing 

console, you need to remove the screws holding the left and 

right side panels. Use these screws to fasten the two wings 

onto the console, being careful to note that each wing fits a 

specific side. With the rack mount wings installed, you can 

mount the mixing console in a commercially available 19" 

rack. Be sure to allow for proper air flow around the unit, and 

do not place the mixing console close to radiators or power 

amps, so as to avoid overheating.

panels to fasten the 19" rack mounts.

You will need a large number of cables for the various 

connections to and from the console. The illustrations below 

show the wiring of these cables. Be sure to use only high-

grade cables.

Fig. 3.1: Digital effects module (only X1204USB)

Please use commercial RCA cables to wire the 2-track inputs 

and outputs.
You can, of course, also connect unbalanced devices to the 

balanced input/outputs. Use either mono plugs, or ensure 

that ring and sleeve are bridged inside the stereo plug  

(or pins 1 & 3 in the case of XLR connectors).

The footswitch connects both poles momentarily

Fig. 4.1: ¼" TS connector for foot switch

For unbalanced use, pin 1 and pin 3 have to be bridged

1 = ground/shield

2 = hot (+ve)

3 = cold (-ve)

1

2

3

1

2

3

Fig. 4.2: XLR connections

Fig. 4.3: ¼" TS connector

For connection of balanced and unbalanced plugs,

ring and sleeve have to be bridged at the stereo plug.

Fig. 4.4: ¼" TRS connector