Behringer PRO MIXER DJX USB DJX900USB Manual De Usuario

Descargar
Página de 11
8
PRO MIXER DJX900USB User Manual
(44) 
The MASTER output is for connecting to an amplifier and can be adjusted 
with the MASTER fader  
(18)
.
◊ 
Always turn the power amps on last to avoid inrush currents that can 
easily damage your speakers. And, to avoid sudden and unpleasant 
surprises for your ears, make sure there is no signal at the DJX900USB 
before turning on the power amps. To be sure, slide all the faders to the 
bottom and switch all controls to the zero position.
(45) 
The BOOTH output gives you an additional option of connecting an amplifier 
in order to, for example, feed the signal into your monitors or to bring sound 
to an extra area. The BOOTH output level is regulated by using the BOOTH 
LEVEL control  
(20)
  of the MASTER section.
(46) 
Using the TAPE output you can record your music by connecting devices 
such as tape decks, DAT recorders etc. Unlike the MASTER output, the output 
volume is fixed, making it necessary for you to adjust the input level on the 
recording device.
(47) 
The POWER switch powers the DJX900USB on. You should always make sure 
that the POWER switch is in the “Off” position when initially connecting the 
unit to the mains.
◊ 
Merely switching the unit off does not mean that it is fully 
disconnected from the mains. When not using the unit for prolonged 
periods of time, please unplug the unit’s power cord from the 
power outlet.
(48) 
This is the connector for the power cable. This is where the advantage of 
a sophisticated internal power supply can be seen: the pulse behaviour 
of each amplifying circuit is mainly determined by the voltage reserves 
available. Each mixing console is equipped with numerous operational 
amplifiers (op amps) to process line level signals. Due to limited output of 
their power supplies, many mixing consoles show signs of “stress” when 
subjected to heavy loads. But not your DJX900USB: the sound is always clear 
and transparent.
(49) 
FUSE HOLDER / VOLTAGE SETTING. Before connecting the unit to 
the mains, ensure that the voltage setting matches your local voltage. 
Blown fuses should only be replaced by a fuse of the same type and rating. 
On some units, the fuses holder can be switched to one of two positions, 
i.e. 230 V and 120 V. Please note: should you desire to operate the unit 
outside Europe at 120 V, a higher fuse rating is required.
◊ 
To disconnect power from main, pull out the main cord plug. 
When installing the product, ensure that the plug is easily accessible. 
If mounting in a rack, ensure that the mains can be easily disconnected 
by a plug or by an all-pole disconnect switch on or near the rack.
(50) 
SERIAL NUMBER.
(51) 
The DJX900USB has built-in USB connectivity, allowing stereo signals to be 
sent to and from the mixer and a computer. The audio sent from the mixer to 
a computer is identical to the TAPE signal. Audio being sent from a computer 
to the mixer can be selected with the Channel 1 LINE/CD/USB switch. 
◊ 
Connect a USB type B plug into the USB jack on the mixer, and the 
other end into a free USB port on your computer. There are no required 
drivers, but we recommend that PC users install the included ASIO 
driver. The driver can also be downloaded from behringer.com.
10.  Initial Operation
◊ 
Ensure adequate air supply and to avoid overheating do not place the 
unit near radiators etc.
◊ 
Before you connect your unit to the mains, please make sure that your 
local voltage matches the voltage required by the unit. The fuse holder 
on the mains connector has 3 triangular markings, with two of these 
triangles opposing each other. The unit is set to the operating voltage 
printed next to these markers and can be set to another voltage by 
turning the fuse holder by 180°.
!
!
Caution
Please note that when operating the unit at 120 V, a higher fuse 
rating is required. Please refer to the “Specifications” for details. 
If you set the unit to a different mains voltage, be sure to use a fuse of the correct 
type and rating. Please refer to the “Specifications” for details.
◊ 
Blown fuses must be replaced by fuses of the correct rating! 
Please refer to the “Specifications” section for the applicable rating. 
Before you change the fuse, switch off the device and pull the plug to 
avoid electric shock or damage to the device.
The mains connection is made using the enclosed power cord and a standard IEC 
receptacle. It meets all international safety certification requirements.
◊ 
Please make sure that all devices are properly grounded. For your own 
safety, never remove or disable the ground conductors from the devices 
or on the power cords. The unit must always be connected to the mains 
outlet with a protective grounding connection.
◊ 
The sound quality may diminish within the range of powerful 
broadcasting stations and high-frequency sources. Increase the 
distance between the transmitter and the device and use shielded 
cables for all connections.
(47)
(44) (45) (46)
(42) (43)
(39)
(38)
(50)
(41)
(48)
(49)
(51)
(40)