Behringer DJX700 Manual De Usuario
ENGLISH
PRO MIXER DJX700 User Manual
7
Merely switching the unit off does not mean that it is
◊
fully disconnected from the mains. When not using the
unit for prolonged periods of time, please unplug the
unit’s power cord from the power outlet.
unit for prolonged periods of time, please unplug the
unit’s power cord from the power outlet.
This is the connector for the power cable. This is where the
[48]
advantage of a sophisticated internal power supply can
be seen: the pulse behaviour of each amplifying circuit is
mainly determined by the voltage reserves available. Each
mixing console is equipped with numerous operational
amplifiers (op amps) to process line level signals. Due
to limited output of their power supplies, many mixing
consoles show signs of “stress” when subjected to heavy
loads. But not your DJX700: the sound is always clear and
transparent.
FUSE HOLDER / VOLTAGE SETTING. Before connect-
be seen: the pulse behaviour of each amplifying circuit is
mainly determined by the voltage reserves available. Each
mixing console is equipped with numerous operational
amplifiers (op amps) to process line level signals. Due
to limited output of their power supplies, many mixing
consoles show signs of “stress” when subjected to heavy
loads. But not your DJX700: the sound is always clear and
transparent.
FUSE HOLDER / VOLTAGE SETTING. Before connect-
[49]
ing the unit to the mains, ensure that the voltage setting
matches your local voltage. Blown fuses should only be
replaced by a fuse of the same type and rating. On some
units, the fuses holder can be switched to one of two posi-
tions, i.e. 230 V and 120 V. Please note: should you desire
to operate the unit outside Europe at 120 V, a higher fuse
rating is required.
matches your local voltage. Blown fuses should only be
replaced by a fuse of the same type and rating. On some
units, the fuses holder can be switched to one of two posi-
tions, i.e. 230 V and 120 V. Please note: should you desire
to operate the unit outside Europe at 120 V, a higher fuse
rating is required.
To disconnect power from main, pull out the main
◊
cord plug. When installing the product, ensure that
the plug is easily accessible. If mounting in a rack,
ensure that the mains can be easily disconnected by a
plug or by an all-pole disconnect switch on or near the
rack.
the plug is easily accessible. If mounting in a rack,
ensure that the mains can be easily disconnected by a
plug or by an all-pole disconnect switch on or near the
rack.
SERIAL NUMBER.
[50]
Initial operation
Ensure adequate air supply and to avoid overheating do
◊
not place the unit near radiators etc.
Before you connect your unit to the mains, please make
Before you connect your unit to the mains, please make
◊
sure that your local voltage matches the voltage required
by the unit.
The fuse holder on the mains connector has 3 triangular
markings, with two of these triangles opposing each other.
The unit is set to the operating voltage printed next to
these markers and can be set to another voltage by turning
the fuse holder by 180°.
by the unit.
The fuse holder on the mains connector has 3 triangular
markings, with two of these triangles opposing each other.
The unit is set to the operating voltage printed next to
these markers and can be set to another voltage by turning
the fuse holder by 180°.
Caution
!
Please note that when operating the unit at 120 V, a higher
fuse rating is required. Please refer to the “Specifications” for
details.
fuse rating is required. Please refer to the “Specifications” for
details.
If you set the unit to a different mains voltage, be sure to use a
fuse of the correct type and rating. Please refer to the “Specifica-
tions” for details.
fuse of the correct type and rating. Please refer to the “Specifica-
tions” for details.
Blown fuses must be replaced by fuses of the correct rating!
◊
Please refer to the “Specifications” section for the applica-
ble rating. Before you change the fuse, switch off the device
and pull the plug to avoid electric shock or damage to the
device.
ble rating. Before you change the fuse, switch off the device
and pull the plug to avoid electric shock or damage to the
device.
The mains connection is made using the enclosed power cord
and a standard IEC receptacle. It meets all international safety
certification requirements.
and a standard IEC receptacle. It meets all international safety
certification requirements.
Please make sure that all devices are properly grounded.
◊
For your own safety, never remove or disable the ground
conductors from the devices or on the power cords. The
unit must always be connected to the mains outlet with a
protective grounding connection.
The sound quality may diminish within the range of power-
conductors from the devices or on the power cords. The
unit must always be connected to the mains outlet with a
protective grounding connection.
The sound quality may diminish within the range of power-
◊
ful broadcasting stations and high-frequency sources. In-
crease the distance between the transmitter and the device
and use shielded cables for all connections.
crease the distance between the transmitter and the device
and use shielded cables for all connections.
Shipment
Should your BEHRINGER product malfunction, it is our inten-
tion to have it repaired as quickly as possible. To arrange for
warranty service, please contact the BEHRINGER retailer from
whom the equipment was purchased. Should your BEHRINGER
dealer not be located in your vicinity, you may directly contact
one of our subsidiaries.
Corresponding contact information is included in the origi-
nal equipment packaging (Global Contact Information/
European Contact Information). Should your country not be
listed, please contact the distributor nearest you. A list of
distributors can be found in the support area of our website
(http://www.behringer.com).
Registering your purchase and equipment with us helps us pro-
cess your repair claims more quickly and efficiently.
Your product was carefully packed at the factory to ensure safe
transport. Nevertheless, if the box is damaged inspect the unit
immediately for signs of damage.
tion to have it repaired as quickly as possible. To arrange for
warranty service, please contact the BEHRINGER retailer from
whom the equipment was purchased. Should your BEHRINGER
dealer not be located in your vicinity, you may directly contact
one of our subsidiaries.
Corresponding contact information is included in the origi-
nal equipment packaging (Global Contact Information/
European Contact Information). Should your country not be
listed, please contact the distributor nearest you. A list of
distributors can be found in the support area of our website
(http://www.behringer.com).
Registering your purchase and equipment with us helps us pro-
cess your repair claims more quickly and efficiently.
Your product was carefully packed at the factory to ensure safe
transport. Nevertheless, if the box is damaged inspect the unit
immediately for signs of damage.
If the unit is damaged please do NOT return it to us, but
◊
notify your dealer and the shipping company immediately;
otherwise, claims for damage or replacement may not be
granted.
Always use the original box to prevent damage during stor-
otherwise, claims for damage or replacement may not be
granted.
Always use the original box to prevent damage during stor-
◊
age or transport.
Make sure that children cannot play unsupervised with the
Make sure that children cannot play unsupervised with the
◊
unit or its packaging.