Behringer DJ Equipment PMP3000 Manual De Usuario
9
EUROPOWER PMP1000/PMP3000/PMP5000 User Manual
PMP3000/PMP5000: The
(62)
MONO OUT is for connecting a subwoofer.
The PMP5000 has the additional possibility of setting the low-frequency
range for the subwoofer.
range for the subwoofer.
Use the SUB FILTER control
(50)
to adjust the frequency.
The
(63)
FX SEND connector can be used to route the FX SEND signal from
the input channel, for example, to the input of an external effects
device. Since the PMP5000 has two FX controls per input signal (see
device. Since the PMP5000 has two FX controls per input signal (see
(12)
),
both FX SEND 1+2 are present at one jack.
Please note: The SEND signal is in parallel with the FX SEND jacks and
◊
with the effects processor, so that both can be controlled together by
one control.
one control.
For the FX signals, use a 1/4" stereo plug connected as follows: FX 1 = tip;
◊
FX 2 = ring
The
(64)
PHONS/CTRL connector allows you to connect a pair of stereo
headphones or an (active) monitor speaker.
Rear panel
2.5
The mains connection is via a standard
(65)
IEC receptacle. An appropriate power
cord is supplied with the unit.
FUSE HOLDER
(66)
. Before connecting the unit to the mains, ensure that
the voltage setting matches your local voltage. Blown fuses should only
be replaced by fuses of the same type and rating. Please also read the
information given in the “Specifications”.
be replaced by fuses of the same type and rating. Please also read the
information given in the “Specifications”.
Use the
(67)
POWER switch to put your PMP into operation. The POWER switch
should always be in the “Off” position before connecting your unit to
the mains.
the mains.
Please note: The POWER switch does not fully disconnect the unit from
◊
the mains. Unplug the power cord completely when the unit is not used
for prolonged periods of time.
for prolonged periods of time.
SERIAL NUMBER
(68)
.
This is where you find the cooling fan of the unit.
(69)
The PMP5000 has two cooling fans.
OUTPUT A (LEFT)
(70)
provides either the left stereo main signal or the monitor
signal in mono, depending on the operating mode selected (see
(27)
).
NEVER use this output in bridged mono mode.
OUTPUT B (RIGHT/BRIDGE)
(71)
provides either the right stereo main signal,
the main mix signal (mono) or the bridged mono signal, depending on the
operating mode selected.
operating mode selected.
In BRIDGE mode always connect only one loudspeaker with an
◊
impedance of at least 8 Ω to the OUTPUT B jack! NEVER use OUTPUT A in
BRIDGE mode!
BRIDGE mode!
In all other operating modes the impedance of the connected
◊
loudspeaker must not fall below 4 Ω.
Digital Effects Processor
3.
24-BIT MULTI-EFFECTS PROCESSOR
This built-in effects module produces high-grade standard effects such as
reverb, chorus, flanger, delay and various combination effects. The integrated
effects module has the advantage of requiring no wiring. This way, the danger
of creating ground loops or uneven signal levels is eliminated at the outset,
completely simplifying the handling. These effect presets are designed to be
added to dry signals.
reverb, chorus, flanger, delay and various combination effects. The integrated
effects module has the advantage of requiring no wiring. This way, the danger
of creating ground loops or uneven signal levels is eliminated at the outset,
completely simplifying the handling. These effect presets are designed to be
added to dry signals.
Turn down the FX controls in those channel strips whose signals you
◊
don’t wish to process.
Installation
4.
Mains connection
4.1
The mains connection is made using the enclosed power cord and a standard IEC
receptacle. It meets all of the international safety certification requirements.
receptacle. It meets all of the international safety certification requirements.
Blown fuses must be replaced by fuses of the same type and rating.
Please make sure that all units have a proper ground connection.
◊
For your own safety, never remove or disable the ground conductor
from the unit or of the AC power cord.
from the unit or of the AC power cord.
Audio connections
4.2
The inputs and outputs of your BEHRINGER EUROPOWER are unbalanced 1/4" mono
jacks—except for the mono channel line inputs, which are balanced 1/4" stereo
jacks. Of course, all inputs and outputs work with both balanced and unbalanced
connectors. The tape in and outputs are on RCA connectors.
jacks—except for the mono channel line inputs, which are balanced 1/4" stereo
jacks. Of course, all inputs and outputs work with both balanced and unbalanced
connectors. The tape in and outputs are on RCA connectors.
Please ensure that only qualified personnel install and operate the
◊
PMP. During installation and operation, the user must have sufficient
electrical contact to earth. Electrostatic charges might affect the
operation of the unit.
electrical contact to earth. Electrostatic charges might affect the
operation of the unit.
Strain relief clamp
Sleeve
Tip
Sleeve
(ground/shield)
(ground/shield)
Unbalanced ¼" TS connector
Tip
(signal)
(signal)
Fig. 4.1: 1/4" TS connector