Baby Einstein 30886 Manual De Usuario
– 3 –
A Locate the seat pad and
place it upside down on
a firm surface.
a firm surface.
B Unbuckle the straps on
each side of the seat
pad.
pad.
C Unfasten the hook-and-
loop strap and fold back
the two fabric flaps.
the two fabric flaps.
D Hold the seat pad above
the seat frame. Turn the
seat pad so that opening
for the vibration unit is
at the front of the frame
(footrest).
seat pad so that opening
for the vibration unit is
at the front of the frame
(footrest).
E Open the pocket at the
top edge of the seat pad
and slide it over the
backrest frame.
and slide it over the
backrest frame.
F Lift up the two fabric
flaps (shown below).
Slide the two flaps over
and under the footrest
wire.
Slide the two flaps over
and under the footrest
wire.
G Gently tilt the bouncer
backward until the
backrest contacts the floor.
backrest contacts the floor.
H Fasten (buckle) the straps
together on each side,
securing the seat pad to the
frame.
securing the seat pad to the
frame.
NOTE: Do not fasten the
hoop-and-loop patches yet.
That step will occur after the
vibration unit installation.
hoop-and-loop patches yet.
That step will occur after the
vibration unit installation.
Straps with buckles
Fabric flaps
Hook-and-loop strap
Fabric pocket in seat pad
Opening in
seat pad
Fabric flaps lifted
Fabric flaps under
footrest wire frame
Straps fastened
5
Install the batteries in the vibration unit.
The vibration unit requires (3) size C (1.5V) batteries (not
included). Please use alkaline batteries for better
performance.
included). Please use alkaline batteries for better
performance.
CAUTION: Follow the battery guidelines in this section.
Otherwise, battery life may be shortened or the
batteries may leak or rupture.
Otherwise, battery life may be shortened or the
batteries may leak or rupture.
• Always keep batteries away from children. • Do not mix
old and new batteries. • Do not mix alkaline, standard or
rechargeable batteries. • Only batteries of the same or
equivalent type as recommended are to be used. • Install
the batteries so that the polarity of each one matches the
markings in the battery compartment. • Do not short-circuit
the batteries. • Do not store batteries in areas that have
extreme temperatures (such as attics, garages, or automo-
biles). • Remove exhausted batteries from the battery
compartment. • Never attempt to recharge a battery unless
it is specifically marked “rechargeable.” • Rechargeable
batteries are to be removed from the toy before being
charged. • Rechargeable batteries are only to be charged
under adult supervision. • Do not use rechargeable alkaline
batteries in a Ni-Cad or Ni-MH battery charger.
old and new batteries. • Do not mix alkaline, standard or
rechargeable batteries. • Only batteries of the same or
equivalent type as recommended are to be used. • Install
the batteries so that the polarity of each one matches the
markings in the battery compartment. • Do not short-circuit
the batteries. • Do not store batteries in areas that have
extreme temperatures (such as attics, garages, or automo-
biles). • Remove exhausted batteries from the battery
compartment. • Never attempt to recharge a battery unless
it is specifically marked “rechargeable.” • Rechargeable
batteries are to be removed from the toy before being
charged. • Rechargeable batteries are only to be charged
under adult supervision. • Do not use rechargeable alkaline
batteries in a Ni-Cad or Ni-MH battery charger.
A Use a Phillips screwdriver to
loosen the screw that secures
the battery compartment
cover. A retentive washer
keeps the screw from falling
off the cover.
the battery compartment
cover. A retentive washer
keeps the screw from falling
off the cover.
B Temporarily remove the
cover by disengaging the
2 tabs at the side opposite the
screw.
2 tabs at the side opposite the
screw.
C Install the batteries...
•
(If you are replacing
batteries, remove the old
ones first.)
batteries, remove the old
ones first.)
•
Install (3) size C (1.5 V)
batteries, observing the polarity markings embossed
on the bottom of the compartment.
batteries, observing the polarity markings embossed
on the bottom of the compartment.
•
Install each battery by first tilting it so that the
negative (–) end goes in first, pushing slightly against
the coil spring contact. The positive (+) end of each
battery goes in last.
negative (–) end goes in first, pushing slightly against
the coil spring contact. The positive (+) end of each
battery goes in last.
D Replace the battery cover and tighten the screw. Do not
overtighten.
Vibration unit
Battery
cover
Phillips screwdriver
Correct
Incorrect