Whirlpool W10545225B Manual De Usuario
13
Oven Light
The oven light is a standard 40-watt appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the off position.
replacing, make sure the oven and cooktop are cool and the
control knobs are in the off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb, then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
4. Replace bulb, then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
Appliance Outlets
(on some models)
The 120-volt appliance outlet located on the control console may
be used to run portable appliances placed on countertops beside
the range.
The outlet operates independently and is not affected by range
control settings.
NOTE: Do not place portable appliances on the cooktop. Damage
to the portable appliance could result if the cooktop is hot.
be used to run portable appliances placed on countertops beside
the range.
The outlet operates independently and is not affected by range
control settings.
NOTE: Do not place portable appliances on the cooktop. Damage
to the portable appliance could result if the cooktop is hot.
Appliance Outlet Circuit Breaker:
The circuit breaker for the appliance outlet on your range is located
next to the outlet. It is rated for 12 amps.
If the circuit breaker trips, it can be reset by pressing the switch. A
delay of several minutes may be required for the circuit breaker to
cool before it will reset.
next to the outlet. It is rated for 12 amps.
If the circuit breaker trips, it can be reset by pressing the switch. A
delay of several minutes may be required for the circuit breaker to
cool before it will reset.
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call.
www.whirlpool.com
In Canada, reference the Customer Service section at www.whirlpool.ca
Operation
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
Nothing will operate
Power supply cord is unplugged.
Plug into a grounded outlet.
Household fuse is blown, or a
circuit breaker is tripped.
circuit breaker is tripped.
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
continues, call an electrician.
The control displays an F9 or F9
E0 error code.
E0 error code.
The electrical outlet in the home may be miswired. Contact a
qualified electrician to verify the electrical supply.
qualified electrician to verify the electrical supply.
Cooktop will not operate
The control knob is not set
correctly.
correctly.
Push in knob before turning to a setting.
On ceramic glass models, the
oven control lockout is set.
oven control lockout is set.
See the control lock keypad feature in the “Feature Guide.”
Excessive heat around
cookware on cooktop
cookware on cooktop
Cookware is not the proper size.
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than
area, element or surface burner. Cookware should not extend
more than
¹⁄₂" (1.3 cm) outside the cooking area.
Cooktop cooking results not
what expected
what expected
Control knob set to incorrect heat
level
level
See “Cooktop Use” section.
Range is not level.
Level the range. See the Installation Instructions.
Cooktop element cycles on
and off on High setting.
and off on High setting.
Element cycling due to a
temperature limiter
temperature limiter
This is normal operation. The element may cycle on and off to
keep the cooktop from overheating.
keep the cooktop from overheating.
Oven will not operate
Delay start is set.
See “Cook Time” section.
Control lock is on.
Press and hold START for 3 seconds to unlock.
Control is in Demo Mode.
Press and hold START TIME for 10 seconds to exit Demo
Mode. Demo Mode is used for display models in a showroom.
Mode. Demo Mode is used for display models in a showroom.
Electronic oven control set
incorrectly
incorrectly
See “Electronic Oven Controls” section.
Oven temperature too high or
too low
too low
Oven temperature needs
adjustment.
adjustment.
See “Oven Temperature Control” in the “Electronic Oven
Controls” section.
Controls” section.
Oven indicator lights flash
Power to range is turned on or
restored.
restored.
See “Control Display” in the “Electronic Oven Controls”
section. If the indicator lights keep flashing, call for service. See
cover for contact information.
section. If the indicator lights keep flashing, call for service. See
cover for contact information.