Siemens SITRANS FUS1010 NEMA-4X/ IP 65 Clamp-On Multi-Function Flowmeter Manual De Usuario
B-3
1010NFM-3J
Appendix
Signal
PC DB-9
1010P/1020N
1010WP
1010N
1010X
Name
Terminal
Terminal Terminal Terminal Terminal
Ground
Pin 5
Pin 5
Pin E
TB1- pin 6
TB2-pin 16
Tx
Pin 2
Pin 3
Pin C
TB1- pin 1
TB2-pin 11
Rx
Pin 3
Pin 2
Pin B
TB1- pin 4
TB2-pin 14
HOW TO USE THE Windows HyperTerminal PROGRAM
Windows provides a communication program called HyperTerminal, which is ideal for interfacing your
computer with the flowmeter. The following typical example explains how to set up HyperTerminal.
NOTE: Depending upon the Windows applications being used this setup procedure may vary.
computer with the flowmeter. The following typical example explains how to set up HyperTerminal.
NOTE: Depending upon the Windows applications being used this setup procedure may vary.
1. From the Windows desktop, left-click on the [START] button.
2. Holding down the left mouse button, move the highlight up to [Programs], then across to [Accesso-
ries]. Slide the highlight down to [HyperTerminal], then release the left mouse button.
3. Within the HyperTerminal window, move the mouse pointer down to [Hyperterm.exe] and then
double-click the left mouse button.
4. This selects the [Connection Description] dialog box. Enter a name for your connection (e.g.,
1010N). You can optionally select an icon for this connection by clicking on one of the icons
displayed in the scrolling frame at the bottom of the window. Click [OK].
displayed in the scrolling frame at the bottom of the window. Click [OK].
5. This selects the [Phone Number] dialog box. Move the cursor to the arrow at the right of the
[Connect Using] field. Left click on the arrow to expand the field and then move the highlight down
to [Direct to Com 1 (or 2)] depending on the port connected to the interface cable. Click [OK] to
select the [Com 1 (or 2) Properties] Dialog box. Set up your RS-232 parameters as shown in the
example below. Left-click on the [OK] button.
to [Direct to Com 1 (or 2)] depending on the port connected to the interface cable. Click [OK] to
select the [Com 1 (or 2) Properties] Dialog box. Set up your RS-232 parameters as shown in the
example below. Left-click on the [OK] button.
COMMUNICATING WITH SYSTEM 1010/1020 VIA THE RS-232 INTERFACE
The following sections assume that you are familiar with the basics of using a Windows 3.x or Win-
dows 95/98/NT/2000/XP based communications program. All PC computers provide at least one se-
rial port using either a 9-pin or 25-pin D-type connector. The port designation can be either COM 1 or
COM 2. Usually, when a computer includes two serial ports, COM 1 will be the 9-pin connector and
COM 2 will be the 25-pin connector. However, port designations can vary from manufacturer to manu-
facturer, so you will have to positively identify the COM port you wish to use for the flowmeter interface.
Connect the cable between the flowmeter and your PC using either the 25-pin, 9-pin or USB to RS-
232 adapter connector, depending upon the port’s architecture.
dows 95/98/NT/2000/XP based communications program. All PC computers provide at least one se-
rial port using either a 9-pin or 25-pin D-type connector. The port designation can be either COM 1 or
COM 2. Usually, when a computer includes two serial ports, COM 1 will be the 9-pin connector and
COM 2 will be the 25-pin connector. However, port designations can vary from manufacturer to manu-
facturer, so you will have to positively identify the COM port you wish to use for the flowmeter interface.
Connect the cable between the flowmeter and your PC using either the 25-pin, 9-pin or USB to RS-
232 adapter connector, depending upon the port’s architecture.
1
5
6
9
PC DB-9 Connector
1010P/1020N/990P Connector
(Wiring Side View)
H
A
B
G
K
J
C
F
E
D
1010WP/WDP Connector
(Wiring Side View)