Knoll Systems Stereo System MR64 Prospecto

Changing Sources. To change to another source

press and release the MR64 keypad INPUT button
followed by the UP or DOWN button to scroll

through the four sources until the desired source is

displayed on the MR64 display. The amplifier for this

room will then switch to this source.

To change sources in this room only from the RB8

remote control simply press the 1, 2, 3 or 4 button
to directly go to the desired source.

Volume Up and Down:

To adjust the volume up

or down (always) first press the MR64 VOL button

then quickly press the UP or DOWN button until the

desired changed volume level is reached on the
MR64. Holding the button gives continuous changes.

After the UP or DOWN button has been released the

MR64 keypad may display the current relative
volume setting of low, mid, high etc.

To change the volume using the RB8 remote press
the UP or DOWN button until the desired changed

volume level is reached on the MR64. Holding the

button gives continuous changes. After the UP or

DOWN button has been released the MR64 keypad
may display the current relative volume setting of

low, mid high etc.

Mute: Momentarily press the M

keypad or RB8 remote MUTE

button. The LCD display will
display:

R64

utton

ill

Power: switches

room off or whole

house off(press

for 5 seconds)

To restore the sound press the MUTE, UP or DOWN

button on the MR64 keypad or RB8 remote and the
source selected when the mute button was first

pressed and the former volume level is restored.

Turn Room Off: Momentarily
press the MR64 keypad OFF b

or RB8 remote POWER button.

The MR64 will display:

If any other room was turned on, only this room will

shut off and other rooms will not be affected. If this

was the only room turned on since the system was
first turned on, then the whole

system will shut off and the MR64

will display a few seconds later:

Sources may have to be turned off manually or by

remote.

ALL System Commands

The ALL button is used to change the whole house

volume (only for rooms already turned on), select
one source for all rooms or turn all rooms off.

All commands are from the MR64 keypads only and

cannot be done from the remote control.

♦To change all rooms to the same source, this room
must be listening to a source first. Press the ALL

button, quickly press the INPUT button then the UP

or DOWN button until the desired source is
displayed on the LCD display. All of the rooms will be

now be playing that source at about 30% volume.

Note: Be very careful when turning up the

whole house volume. The volume levels

increase together, but rooms with their volume
already set high may damage equipment when

their volume is increased.

♦To change the whole house volume, this room must
be listening to a source first. Press the ALL button,

quickly press the VOL button then the UP or DOWN

button until the desired volume in all rooms is
achieved. Please note all rooms will not necessarily

be at the same volume as some may have initially

been at a higher or lower volume and had the
volume changed from that point. The whole house

volume changes more gradually than when changing

individual room volumes.

♦To turn the whole home system off (except for
sources), press the ALL button then quickly press
the OFF button. The whole

system will start its turn off

procedure. The LCD keypad w
display:

Another way to achieve turning the whole system off
is to press the MR64 OFF button for about 5

seconds. To turn the whole home system off from

the RB8 remote control, press

the POWER button for about 5
seconds. The MR64 keypad will

then display:

RB8 Remote Layout

POWER

MUTE

VOL

INPUT

RB8

systems

Input 1-4: Turns

on room and

selects input

music source

Mute: Mutes music.

to restore, press

mute, input 1-4 or

volume up/down

Volume Up/Down

Press and hold

for continuous

volume changes

System

Off

Mute

System

Off

Zone

Off

System

Off

Source

xxxx