CAT Titan 250 Manual De Usuario
Turbomachinery Package Specification
Titan
250 Generator Set
Figure 11. Typical Lube Oil System
8.1.7
Lube Oil Vent Flame Arrestor
The lube oil vent flame arrestor prevents an ignition source from entering the lube oil
tank. The flame arrestor is loose shipped for offskid installation by others.
tank. The flame arrestor is loose shipped for offskid installation by others.
8.1.8
Lube Oil System Options
Lube Oil Cooler
An air-to-oil type cooler is available to provide oil cooling for the gas turbine and the
driven equipment. The cooler is sized for specified heat loads and ambient temperatures
and is designed for a 4.4°C (40°F) approach temperature. The cooler is loose shipped for
offskid installation by others.
driven equipment. The cooler is sized for specified heat loads and ambient temperatures
and is designed for a 4.4°C (40°F) approach temperature. The cooler is loose shipped for
offskid installation by others.
Lube Oil Immersion Tank Heater
The lube oil tank immersion heater ensures the lube oil tank temperature is adequate for
starting in cold conditions. The tank heater also facilitates a short lube oil temperature
warm up period after a cold start. Electrical supply contactors are not included.
starting in cold conditions. The tank heater also facilitates a short lube oil temperature
warm up period after a cold start. Electrical supply contactors are not included.
Table 6.
Lubrication System Specifications
Main Lube Oil Pump
Pump Type
Engine-Driven Rotary Screw
Flow
1999 lpm (528 gpm)
Discharge Pressure
690 kPag (100 psig), See Note (a)
Pre/Post Lube Oil Pump
Pump Type
AC Motor-Driven Centrifugal
Optional Motor Voltage Ratings
380 VAC, 400 VAC, and 415 VAC (50 Hz)
460 VAC and 575 VAC (60 Hz)
460 VAC and 575 VAC (60 Hz)
Motor, Power
7.45 kW (10 hp)
Backup Lube Oil Pump
Pump Type
DC Motor-Driven Centrifugal
Motor Voltage Rating
120 VDC
Motor, Power
7.45 kW (10 hp)
Lube Oil Cooler
Lube Cooler Oil Volume (Per Cooler)
Project Specific
Design Heat Load (Per Cooler)
Project Specific
Design Oil Flow Rate (Per Cooler)
Project Specific
Air Flow Rate
Project Specific, See Note (b)
Maximum Ambient Temperature
43°C (110°F)
Maximum Design Lube Oil Cooler Outlet
Temperature
Temperature
66°C (150°F)
Maximum Lube Oil Cooler Design Pressure Drop
173 kPag (25 psig), See Note (c)
Minimum Lube Oil Cooler Design Pressure
1 035 kPag (150 psig)
Optional Motor Voltage Ratings
380 VAC, 400 VAC, and 415 VAC (50 Hz)
460 VAC and 575 AC (60 Hz)
460 VAC and 575 AC (60 Hz)
Optional Motor, Power
7.5 kW (10 hp), 15 kW (20 hp), or 2 x 15 kW (20
hp)
hp)
Lube Oil Tank Immersion Heater, See Notes (d) and (e)
Optional Voltage Ratings
380 VAC, 400 VAC, and 415 VAC (50 Hz)
460 VAC and 575 VAC (60 Hz)
460 VAC and 575 VAC (60 Hz)
Power
3-Phase VAC, 40 kW
Minimum/Maximum Regulated Supply Pressure
100 to 225 psig (689 to 1551 kPag)
© 2008 Solar Turbines Incorporated. All rights reserved.
TPS250GS/908 - Preliminary
26